WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 1
Owner’s Manual EN
Head Unit for 2014+ Harley-Davidson® Touring Motorcycles
w/ iGo® GPS Navigation, Wireless Apple® CarPlay®, Wireless
Android Auto®, iDataLink® Maestro® Compatible,
SiriusXM® Ready®, & 8.3” LCD Touchscreen
GPS
NAVIGATION
Wireless Rally Wide
Headset
Integration
Mode TM
Music Sharing
8” screen
LCD
15-BAND 5-VOLT 2-OHM IPx5
EQUALIZER RCA AUDIO 4ch. SPEAKER WATERPROOF
& CROSSOVERS OUTPUT AMPLIFIER FACEPLATE
V2WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 2
Contents Safety First
Safety First Safety Definitions
Safety Definitions 2 Statements in this manual preceded by following
words are of special significance:
Pre-Riding
Check list 3 WARNING
Care and cleaning 3 WARNING indicates a potentially hazardous
Screen 3 situation which, if not avoided, could result
in death or serious injury.
Accessories & Installation 4
Installation 5 WARNING
Set volume levels and other controls on
Wiring 6
audio and electronic devices before riding.
Harness 8 Distractions can lead to loss of control,
Operation resulting in death or serious injury.
Main menu 8 WARNING
Setting 9
Apple CarPlay/Android Auto 14 Do not select a volume level that blocks out
Radio operation 18 traffic noise or interrupts the concentration
SiriusXM 19 necessary for the safe operation of the Motor-
USB operation 24 cycle. Distractions or a volume level that
Bluetooth Music 25 blocks our traffic noise could cause loss of
Bluetooth Phone 25
control resulting in death or severe injury.
Headsets 25
Rally Mode 27
GPS Navigation Powered by iGo Note
Primo® 27
Pay attention while riding, keeping your eyes and
iData Link 75 clear mind on the road. Some features are locked out
Camera in 77 to prevent distraction, limited in capability while the
Motorcycle isin motion. Even a part is available, donot
Specification 78 allow it to distract you from operating your
Motorcycle safely.
Trouble Shooting 79
FCC Notes 80 For safety, program the system when stopped.
Perform system setup and get familiar with the
controls and features of the infotainmentsystem
before operating the Motorcycle on the road.
This system cannot warn about the safety of an area,
bad road conditions, and availability of emergency
services.
Use this radio only in locations where it is safe to do.
2WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 3
Pre-RIDING Appearance
Check list
Configure the system with your personal
preferences before riding to use features and
minimize distractions while on the road
entirely.
1. Set brightness, background.
2. Configure global presets.
3. Adjust audio settings like EQ, volume, fade,
balance etc. before ridding.
4. Pair, connect and set up phone features
through Bluetooth.
5. Connect USB devices for Apple CarPlay® or Front
Android Auto®.
6. Selectstation or media
7. Connect the iDataLink Maestro module for
Motorcycle Info and Gauage information
display.
CARE AND CLEANING
Use only V2 recommended products and
methods to keep the radio, speakers, and other
audio system components clean and in good
condition.
Do not use any abrasives, polishes, or rubbing
compoundsto clean the screen or other
components. Do not use any ammonia-based
cleaners on the net.
The use of other products or methods may
cause damage to components.
Screen : Top
Do not use any chemical cleaners or
chemical-containing wipes or cloths.
These can cause damage to the screen
surface.
Gently clean the display glasssurface with a
clean, dry microfiber cloth. Before cleaning, it
is suggested to remove any visible dust, dirt,
sand particles with a gentle compressed
airstream.
Back
3WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 4
Accessories and Installation
Harness Included!
Installation
Use OEM head unit mounting locations & original screws
4
WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 5
Installation
Note: Reinstall the OEM bracket after head unit installation
Installation 1 USB Connector
Connect the OEM USB cable for USB
device, Android smart phone, iPhone.
2 GPS Connector
Connect the GPS Antenna.
3 Radio Connector
9 Connect the Radio Antenna.
4 Camera in
Connect the Camera in.
5 Camera +12 V DC (Max 0.5A)
8 Connect the Camera power cable.
6 External Microphone Connector
Connect the external Microphone cable.
1 7 Type-C USB Connector
Connect the external device for charging.
8 Bluetooth Antenna
2 Bluetooth Antenna for Rally mode.
3 7 9 SiriusXM Tuner Connector
4 Connect the SXV300 tuner.
5 6 Note: SiriusXM SXV300 Tuner sold separately,
SiriusXM subscription required.
5WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 6
Wiring
Connect the OEM GPS,USB and radio antenna cables disconnected during removal of
the OEM head unit to matching SOCKETS on the back of V2. If all are difficult to connect,
verify the orientation of the connector(s) is correct. If any afternarket audio amplifiers will be
used in the audio system,take a moment to connect the RCA cables to the corresponding
audio outputs. Although not required, if the Bluetooth calling microphone will be used,se-
cure it to the desired installation location, then route its cable to the
corresponding input on the back of v2.
OEM USB Cable Connector
(USB cable not included)
SXM Tuner(Not included)
USB Type-C for
Charging
Bluetooth Antenna
3.5mm Connection for Included
GPS Antenna Cable (Included) Bluetooth Calling Microphone
(Or you can use OEM GPS Antenna Cable) Camera in (Yellow)
CAM +12V(Max0.5A)(Pink)
RCA Low-Level Subwoofer Output for
OEM Radio Antenna Connector
(antenna cable not incl.) Aftermarket Subwoofer Amplifer (RCA Included)
RCA Low-Level Rear Channel Output for
Aftermarket Speaker Amplifer (RCA Included)
RCA Low-Level Front Channel Output for RCA Low-Level Front Channel Output for
(RCA not incl.)
Aftermarket Speaker Amplifer (RCA Included)
48 PIN CONNECTOR
E4. Pink/White............UART-SPEED L1. White/Black.........FL-
F4. Gray/White...........UART-TX L2. White.......................FL+
G4. Blue/White...........UART-RX L3. Black.........................Ground
H1. Green/Black.........RL- L4. Black.........................Ground
H4. Red/White............UART-12V M1.Gray.........................FR+
J1. Green.......................RL+ M2.Gray/Black...........FR-
J3. Orange/Whike...Illumination M3.Yellow.....................Battery+
J4. Black/White.........UART-GND M3.Yellow.....................Battery+
K1. Purple......................RR+
K2. Purple/Black........RR-
K3. Blue...........................ANT
K4. Red...........................ACC
6WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 7
Included Harness
Harness! Connect to Motorcycle: Connect to V2 (Headunit):
1. CAN- （Green/White) 3- Pin Connector
8. RL-（Green/Black) 3
Black......................... Ground
9. RL+ （Green) Red.............................ACC
10. RR+(Purple)
1
Yellow......................Battery
11. FL-(White/Black) 4- Pin Connector
12. FR+(Gray) Blue/White...........UART-RX
1
13. CAN+( Purple/White) Gray/White..........UART-TX
14. Remote Control(Blue) Black/White.........UART-GND
4
22. RR-(Purple/Black) Red/White............UART-12V
23. FL+(White) 10- Pin Connector
24. FR-(Gray/black) 1.Orange/White............Illumination
35. GND(Black) 2 1 5.Pink/White....................SPD
36. Battery +(Yellow) 7.Blue/White....................UART-RX
42. UART-RX(Blue/White) 10 9
8.Blue.................................Auto Amplifier
47. GND(Black) 9.Blue....................................Remote Control
48. Battery + (Yellow) 10.Blue....................................Remote Control
18- Pin Connector
CAN+.................... Green /White
CAN-...................... Purple /White
Connect to External Amplifier:
Rr
Connect to iDatalink Maestro Rr2 Compatible：
Note: The Maestro Box is not included.
7WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 8
Main Menu
V2 is a headunit for 2014+ Harley-Davidson® Page 1
Touring Motorcycles w/ iGo® GPS Navigation,
Wireless Apple® CarPlay®, Wireless Android
Auto®, iDataLink® Maestro® Compatible,Siri-
usXM® Ready®, & 8.3” LCD Touchscreen
Touch the corresponding Mode icon to enter
playing mode. The Mode icon in gray means
the corresponding function is not ready, or
the proper device has not been connected.
Page 2
Home Page:
1 2 3 4
How to move the APP icon to the home page :
Press and hold the prefer icon, and drag the icon to
6 5 home page.
The home page bottom 6 shortcut icons will be activate .
1.Display current riding speed.
Select prefer icon to exchange.
2.Display the now playing source information.
3.Display headset connected information.
No connection
Press to start search the avaliable
headset to connect.
2) When connect 1 headset device
Press to select the media sound
routing headset or motorcycle
speaker.
3) When connect 2 headset devices
Press to select the intercom is
On or Off.
4.Display the motorcycle base information.
5.Shortcut buttons.(These 7 shortcut can be
exchanged with APPs page icon.)
6. Tap to enter APPs Page:
8WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 9
Settings
Tap to activate pop-up settings menu: In APPs page 2, press <Setting> icon to access
1 to settings page.
System settings as below: Language , Date &
Time, Touch Feedback, Factory Reset,Camera
View, GPS Signal, About.
1 2
Language:
Select the prefer language for operation.
7 3 5 6 9 8 4
1.Press to Mute or Un-Mute.
2.Decrease / Increase now playing source volume. Date & Time:
3.Press to select Daytime or Nighttime. Set the time and time format.
4.Decrease / Increase the panel brightness.
5.Press to access to Settings page.
6.Press to swith the routing Headset or Speaker.
Note: If the headset is not connected, the button
will be gray color and disable.
7.Press to access the EQ settings page.
8.Press to access to the Camera video in.
9.Press to hide the Pop-up menu.
Touch Feedback:
Set the Key Beep is ON or OFF.
9WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 10
Settings
Factory Reset: Display settings as below: Background wallpaper,
Reset Factory Data, press it to pop-up dialog box, Brightness.
you can select “OK” or “Cancel”.
Background Wallpaper:
Camera View: Select the prefer preset wallpaer .
Set the Camera View is Normal or Reverse.
GPS Signal:
Once receive the GPS signal, will display the
signal / satellite number.
About:
Press to display the headunit software information,
serial number. Or you can press “+” to custom wallpa[er from USB
And you can update the software via USB. device.
Select a picture and touch ”OK” to add the
wallpaper.
Select another picture for replacing
the current wallpaper.
Brightness:
Set the Day / Night time screen brightness.
Night Mode Auto is ON status, you can set the
Start / Exit time by manually.
10WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 11
Settings
Audio Setting About the Crossover
Below shown is the Audio serring Menu. This unit is equipped with an active crossover. The
crossover limits the frequencies delivered to the
outputs.
The crossover adjusts the HPF (high pass filter) or LPF
(low pass filter) of speakers and subwoofer, and also
the slope (how fast the filter rolls off the highs or
lows).
Adjustments should be made according to the
reproduction characteristics of the speakers.
Depending on the speakers, a passive network may
Fade & Balance:
not be necessary. If you are unsure about this point,
Select the prefer language for operation. please consult your authorized Alpine dealer.
• HPF (high pass filter): Cuts the lower frequencies and
allows the higher frequencies to pass.
• LPF (low pass filter): Cuts the higher frequencies and
allows the lower frequencies to pass.
• Slope: The level change (in dB) for a frequency change .
• The higher the slope value, the steeper the slope
becomes.
Touch the L or R of Balance/ Fade to • Do not use a tweeter without the HPF set on, with a
tune for the driver and passenger high cut-off frequency, otherwise damage may occur to
preference. the speaker due to the low frequency content.
The value of Balance (Left 12 – Right 12) • Adjustment should be made according to the
and Fader (Front 12 – Rear 12). recommended crossover frequency of the connected
Touch Reset to set both Balance and Fader speakers. Determine the recommended crossover
to zero. frequency of the speakers. Adjusting to a frequency
15-Band Equalizer: range outside that recommended may cause damage
15-band of EQ tuning, slide the EQ bar to tune to the speakers.
each band frequency level according to use For the recommended crossover frequencies of
preference. speakers, refer to the respective Owner’s Manual.
Touch Reset button to sell all Band to zero. We are not responsible for damage or malfunction of
speakers caused by using the crossover outside the
recommended value.
Or user can touch “ ” at the bottom to activate
>
preser EQ list, then select the prefer one.
3D Surround is On / Off.
11WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 12
Settings
Front/ Rear Crossover:
AMP Turn-on Delay: ON /OFF.
User can set AMP Turn-on Delay is ON or OFF.
Volume Settings:
User can set Source Level / Maximum Volume
/ Defult Audio.
Slope： 12dB / 24dB
Set Font Crossover Set Low Pass Crossover
Frequency & Slope. Frequency & Slope.
User can touch “<” or “>” to select the desired
frequency Value.
Source Level Adjust.
Subwoofer Settings:
UserSiriusXM
can adjust the source mode (Radio,
Subwoofer Output: ON or OFF. USB, BT Audio,Apple CarPlay, Andriod Auto,
Subwoofer Level: -10~+10 SiriusXM) gain value. The gain can be
Subwoofer Crossovers: adjusted from -5~+5 seperatedly.
Maximum Volume Adjust.
Set Low Pass Crossover
Frequency & Slope.
Slope： 12dB / 24dB Maximum Volume Level : ON or OFF.
Set High Pass Crossover Frequency & Slope. Maximum Level Adjust: 0~40
User can touch “<” or “>” to select the desired
frequency Value.
Subwoofer Phase: 00 or 1800
User can touch “<” or “>” to select the 00 or 1800
12WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 13
Settings
Default Audio. Wifi Settings：
Touch the Wifi Settings from the setting
menu will be shown as below:
User can adjust the default audio (Main, BT
Talking, Navi , Voice,) gain value. The gain
can be adjusted from 0~40 seperatedly. Wi-Fi : On/Off (Select WIFI connection
is On or Off).
Bluetooth Settings：
Touch the Bluetooth Settings from the setting Password : Shown the device wifi password.
menu will be shown below: Password Reset: To reset the password.
Connection : On/Off (Select Bluetooth connection
is On or Off).
Search： To start the paring.
Device Name : Shown the connected phone or
device name.
Clear Records: To clear the device list records.
Mic Gain : Set the Mic Gain (High / Mid / Low).
13WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 14
Apple CarPlay® & Android Auto®
Apple CarPlay :
Starting procedure of using Apple CarPlay
You can operate iPhone applications with
1 Connect an Apple CarPlay compatible
finger gestures such as tapping, dragging,
device to this unit via USB.
scrolling, or flicking on the screen of this
2 Touch the Apple CarPlay icon.
product.
The Apple CarPlay home screen appears.
Compatible iPhone models
For details about compatibility of iPhone You can use Apps of connected iPhone. The
models, refer to the following website. items displayed and the language used on the
https://www.apple.com/ios/carplay screen differ among the connected devices.
To enter the Apple CarPlay mode, touch Apple
WARNING Carplay icon on the Home selection screen.
Certain uses of the iPhone may not be legal 1
while driving in your jurisdiction, so you must
be aware of and obey any such restrictions. If
in doubt as to a particular function, only
perform it while the car is parked. No feature
should be used unless it is safe to do so under
the driving conditions you are experiencing.
Notes on using Apple CarPlay
• iPhone with iOS 7.1 or later is required.
Update to the latest iOS version before use. 2 3
• Apple CarPlay can be used on iPhone 5 or
later.
• For details on compatible models, refer to 1 Application keys
the compatibility list on the support site on the
back cover. Start the application.
• For details about Apple CarPlay, refer to the
manual supplied with your iPhone, or visit the 2
website of Apple CarPlay.
Display the home screen of Apple CarPlay.
• Since the GPS on your iPhone is used, place
Touch and hold to active Siri.
your iPhone where it can easily receive a GPS
signal 3 Home
Exit the Apple CarPlay screen and displays
• You can use Siri function by touching Home screen.
button once Apple CarPlay is activated
• The Bluetooth connection with the Apple * The icon design may change depending
CarPlay compatible device will be terminated on the iOS version.
automatically if Apple CarPlay is turned on.
• Hands-free phoning via Bluetooth wireless
technology is not available while Apple
CarPlay is on.
14WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 15
Apple CarPlay® & Android Auto®
How to connect Wireless Apple CarPlay The user also can use the iPhone
Starting procedure of using Wirelessly Apple
search the device via Bluetooth , then
CarPlay follow the pop notice step by step to
Before using Apple CarPlay wirelessly, turn on connect
the Bluetooth function on the iPhone. 1. Turn on your iPhone’s
Bluetooth and Wi-Fi, and Soundstream V2
MagiCast_1104
Soundstream V2
connect to Soundstream
1 On the Main menu tap the icon access V2.
to Device Link interface. a. Go to Settings >
Bluetooth and the phone
Show below pop-up menu, tap YES start to should be able to find a Soundstream V2
search the available devices. Bluetoot Device(Sound-
stream V2) .
b. A Bluetooth Pairing Request will be displayed on
the screen with a specific code which should match
what is shown on. Tag “Pair” for connecting.
c. Immediately following the Pairing notification, a
new request to “Allow Contacts and favorites Sync”
on your iPhone, Allow in order to have caller ID and
2. When the headunit detect the available access to your contacts through CarPlay.
device, follow the pop-up notice step by step
：Following the BT connection, there is no
to connect the iPhone. After connected, will
need to try and connect WIFI manually (although it
show below page:
does need to be ON), after the BT connection
1 2 3 4 process is complete, the WIFI will connect automati-
cally on its own.
3.Wait for a moment for CarPlay connection, click
use CarPlay and enter the UI interface.
4. iPhone will pop-up prompts, click “Use CarPlay”.
Android Auto®:
You can operate Android applications with
finger gestures such as tapping, dragging,
1. Tap to start to search new device. scrolling, or flicking on the screen of this
product
2. Tap to access Apple CarPlay interface.
3. Tap to access Bluetooth interface. Starting procedure of using Android Auto
4. Tap to delete current device. 1 Connect an Android Auto™ compatible
device to this unit via USB.
2 Touch the Android Auto icon.
The Android Auto home screen appears
15WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 16
Apple CarPlay® & Android Auto®
Note:
• You can use Voice function by touching 3 Operation Bar
button once Android Auto is activated. Starts the application or displays informa-
• The Bluetooth connection with the Android tion.
Auto compatible device will be terminated
automatically if Android Auto is turned on. How to connect Wireless Android Auto
• Hands-free phoning via Bluetooth wireless Starting procedure of using Wirelessly Android
technology is not available while Android Auto
Auto is on.
Notes on using Android Auto 1 On the Main menu tap the icon access
• Android phone with Android 5.0 or higher is to Device Link interface.
required. Update to the latest OS version
before use. Show below pop-up menu, tap YES start to
• Your Android phone needs to support search the available devices.
Android Auto. For details on compatible
models, refer to the compatibility list on the
support site on the back cover.
• Download the Android Auto app on Google
Play.
• For details about Android Auto, refer to the
manual supplied with your Android phone, or
visit
• Since the GPS on your Android phone is used,
place your Android phone where it can easily
receive a GPS signal. 2. When the headunit detect the available
• Android Auto may not be available in your device, follow the pop-up notice step by step
country or region.the website of Android Auto. to connect the iPhone. After connected, will
show below page:
1
3
1 2
2 3 4
1 Application keys
Start the application. 1. Tap to start to search new device.
2 Home 2. Tap to access Android Auto interface.
Exit the Android Auto screen and displays 3. Tap to access Bluetooth interface.
Home screen. 4. Tap to delete current device.
16WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 17
Apple CarPlay® & Android Auto®
The user also can use the Android Smartphone search the
device via Bluetooth , then follow the pop notice
step by step to connect wireless Android Auto.
1. Turn on your phone’s
Bluetooth and Wi-Fi, and
connect to Soundstream V2.
MagiCast_1104
a. Go to Settings > Bluetooth
and the phone should be able
to find a Bluetooth Device(-
Soundstream V2) .
b. A Bluetooth Pairing Request will be displayed on the
screen with a specific code which should match what is
shown on. Tag “Pair” for connecting.
c. Immediately following the Pairing notification, a new
request to “Allow Contacts and favorites Sync” on your x
Android smartphone, Allow in order to have caller ID
and access to your contacts through Android Auto.
Note：Following the BT connection, there is no need to
try and connect WIFI manually (although it does need
to be ON), after the BT connection process is complete,
the WIFI will connect automatically on its own.
3.Wait for a moment for Android Auto connection,
click use Android Auto and enter the UI interface.
4. Android Phone will pop-up prompts, click “Use
Android Auto”.
17WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 18
Radio
Touch “Radio” in the main menu to enter the 1. Favorite list (Global preset), user can store
radio interface. favorite AM/FM/SixiusXM station, then
1 2 3 4 5 6 7 select it for playback directly.
Once tap one station, will back to playback
page.
2. Tap to show previous list page.
3. Tap to show next list page.
Search station list
1
8 9 10 11 12 13 14 15
1. Tap to back to home page.
2. Short press to seek down, Long press to
step down.
3. Tap to store current station as one favorite
station.
4. Show current staion frequency information. 1. Tap to start to search available station,
5. Show current station Radio Text. press one station and back to radio playback
6. Show PTY information. page.
7. Short press to seek up, long press to Radio settings:
step up.
8. Frequency scroll bar, user can choose
desired frequency manually.
9. AM button.
10. FM button.
11. SiriusXM Button
12. Favorite list button.
13. Station list button.
14. EQ Button.
15. Settings Button.
Radio Region: Select desired radio region.
Favorite station list e.g: America, Europe...
1 2 3 RDS: Select RDS is ON/OFF.
TP: Select TP is ON/OFF.
TA: Select TA is ON/OFF.
PTY: Tap to access PTY information page.
18WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 19
Sirius XM
you can tune to channels in your subscription
SIRIUSXM® SATELLITE RADIO
plan.
Only SiriusXM- Ready® brings you more of what you
Note：The activation process usually takes 10 to
love to listen to, all in one place. Get over 140
15 minutes, but may take up to an hour. Your
channels, Including commercial-free music, plus
radio will need to be powered on and
the best sports and live events, comedy, news,
receiving the SiriusXM signal to receive the
exclusive talk, and entertainment. Welcome to the
activation message.
world of satellite radio. A SiriursXM vehicle tuner
and subscription are required. Fsold separately,
SiriusXM subscription required). Some SiriusXM channels contain mature content.
For more information, visit When the Parental Controls feature is enabled,
www.siriusxm.com. channels with mature content are restricted and
(SiriusXM service is only available in the continental will require a 4-digit lock code to access.
US and Canada.) To enter SiriusXM Mode, touch the SXM icon on
Activating Your SiriusXM Subscription the Main Menu.
After installing your SiriusXM Connect Vehicle
If the screen is shown “Check Tuner” as below,
Tuner and antenna, power on your SoundstreaM
check the SiriusXM tuner connection.
V2 and select SiriusXM mode. You should be able to
hear the SiriusXM preview channel on Channel 1. If
you cannot hear the preview channel, please check
the installation instructions to make sure your
SiriusXM Connect tuner is properly installed.
After you can hear the preview channel, tune to
Channel 0 to find the Radio ID of your tuner.
In addition, the Radio ID is located on the bottom
of the SiriusXM Connect Vehicle Tuner and it
packaging. You will need this number to activate
your subscription. Write the number down for Touch “SiriusXM” in the main menu to enter the
reference. SXM interface.
Note: the SiriusXM Radio ID does not include
the letters I, O, S or F. 1 2 3 4 5
In the USA, you can activate online or by calling
SiriusXM Listener care:
-Visit www.siriusxm.com/activatenow
-Call SiriusXM Listener Care at
6
1-866-635-2349
For Canadian Subscriptions, please contact: 7
-Visit www.siriusxm.ca/activate
-Call SiriusXM Customer Care at 1-888-539-7474
As part of the activation process, the SiriusXM 12 11 10 9 8
satellites will send an activation message to your
tuner. When your radio detects that the tuner has Radio ID:
received the activation message, your radio will Press channel 0 to display the Radio ID.
display "Subscription Updated". Once subscribed, You can use channel up/down or direct tune.
19WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 20
Sirius XM
1. Tap to back to home page. Artist and Song Alert
2. Tap to playback previous channel While listening to SiriusXM Satellite Radio, user
3. Show current station ID
4. Show current station information. can mark Artists and/or Songs for which you
5. Tap to playback next channel wish to be alerted. The radio will display an Alert
6. Tap to store current station to favorite message when a matching artist or song is
list. found on another channel. Then user can
7. Tap to pop-up the keyboard and enter choose if you want to tune to that favorite or
desired channel number directly. user can ignore the alert and stay on your
8. Tap to access the SXM settings page. current channel. To store an artist or song title,
9. Tap to access to channel list. touch on the "artist" or Song" metadata on the
10. Tap to access Favorite list page.
11. Show the signal strength: Excellent/ display. User will then be prompted to set the
Good/ Weak/ No signal. alert for the Artist or the Song Title. User will be
12. Tap to Alert current station’s Song/ alerted when one of your stored artists or songs is
Artist. playing on another channel. If multiple alerts
happen at the same time, or the alert gets
Direct Tune dismissed, user can touch the ALRT button to
Press to shown the direct tune interface, list the channels that are currently playing your
user can direct enter the channel number and artist or song.
touch “OK” to go to the desire channel.
Press backspace to clear the pervious digit.
Tap “Artist” to alert current artist.
Tap “ Song” to alert current song.
Tap “Cancel” to dismiss the pop menu.
Favorites list
SXM settings
1 2 2
1. Tap to previous page favorite stations.
2. Tap to next page favorite stations.
3. Tap one station and back to playback page.
20WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 21
Sirius XM
Change Pass Code SXM List
Touch "> of the Change Passcode" to show the
below screen. Input the passcode by using the
keypad.
My Alert
Press the My Alerts key to view all stored artist &
song title alerts.
Press Artist / Song to show the stored the alerts.
Tap the delete icon to delete it accordingly.
Parental Controls
Some SiriusXM channels contain mature content.
When the Parental Controls feature is enabled,
channels with mature content are restricted and
will require a 4-digit lock code to access.
Category List
Touch the “Category” for the Category list
Note：
Default passcode is “0000”
Version
Tap “ Version” to show the SXM detailed informa-
tion. Tap “ < / >” to select Category item, the channals will be
shown accordingly.
Channel List
Touch the “Channel” for the Category list
21WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 22
Sirius XM
Change Pass Code SXM List
Touch "> of the Change Passcode" to show the
below screen. Input the passcode by using the
keypad.
My Alert
Press the My Alerts key to view all stored artist &
song title alerts.
Press Artist / Song to show the stored the alerts.
Parental Controls Tap the delete icon to delete it accordingly.
Some SiriusXM channels contain mature content.
When the Parental Controls feature is enabled,
channels with mature content are restricted and
will require a 4-digit lock code to access.
Category List
Touch the “Category” for the Category list
Note：
Default passcode is “0000”
Version
Tap “ Version” to show the SXM detailed informa-
tion.
Tap “ < / >” to select Category item, the channals will be
shown accordingly.
Channel List
Touch the “Channel” for the Category list
22WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 23
Sirius XM
Touch “Artist /Song/ Info / Category / Channel” button
at top bar to display the channel detailed information.
On-Screen Display Advisory Message Cause Explanation / Solution
The radio has detected a fault with • Verify that the SiriusXM Connect Vehicle Tuner cable is
Check Antenna Check Antenna theSiriusXM antenna. The antenna cable securely connected to the radio SiriusXM connector/ cable.
may be either disconnected or damaged. • If the problem persists, disconnect and reconnect the tuner
and then contact your dealer.
•Theradio has difficulty communicating • Verify that the SiriusXM Connect Vehicle Tuner
Check Tuner Check Tuner with the SiriusXM Connect Vehicle Tuner. cable is securely connected to the radio SiriusXM
connector/ cable.
• The tuner may be disconnected or • If the problem persists, disconnect and reconnect
damaged. the tuner and then contact your dealer.
• Verify that your vehicle is outdoors with a clear
view of the southern sky.
• Verify that the SiriusXM magnetic mount antenna
is mounted on a metal surface on the outside the
The SiriusXM Connect Vehicle Tuner has vehicle.
No Signal No Signal difficulty receiving the SiriusXM satellite • Move the SiriusXM antenna away from any
obstructions.
signal. • Inspect the antenna cable for damage and kinks.
Replace the antenna if the cable is damaged.
• If the problem persists, disconnect and reconnect
the tuner and then contact your dealer.
The channel that you have requested is The channel that you have requested is not a valid
not a valid SiriusXM channel or the channel SiriusXM channel or the channel that you were
that you were listening to is no longer listening to is no longer available. You may also see
Channel Not Channel Not available. You may also see this message this message briefly when first connecting a new
Available Available briefly when first connecting a new SiriusXM Connect Vehicle tuner.
SiriusXM Connect Vehicle tuner. Visit Visit www.siriusxm.com or
www.siriusxm.com for more information www.siriusxm.ca for more information about the
about the SiriusXM channel lineup. SiriusXM channel lineup.
• Questions about your subscription in the United
The channel that you have requested is States please visit
Channel Not Channel Not not included in your SiriusXM subscrip- http://www.siriusxm.com/activatenow or call
tion package or the channel that you SiriusXM Listener Care at 1-866-635-2349.
Subscribed Subscribed
were listening to is no longer included • Questions about your subscription in Canada
in your SiriusXM subscription package. please visit
http://www.siriusxm.ca/help/activation-help/ or
call XM Listener Care at 1-888-539-7474
•See the section on Lock Channel, more
The channel that you have requested is information on the Lock Channel feature and how
Channel Locked Channel Locked
Locked by the radio to access locked channels.
Please Enter the Please Enter the User prompted to enter the lock/unlock •Enter the four digit code to unlock the channel
Lock Code Lock Code code.
Incorrect Incorrect • Input the correct four digit code to unlock the
Passcode Passcode The unlock code entered by the user is channel.
incorrect • Reset lock code to default following instructions.
Entered Entered
23WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 24
USB
USB
1. Tap to playback previoust picture.
Plug the USB; the USB icon will be lighted .
2. Tap to select play/ pause.
Touch the USB icon to enter the USB playback mode.
3. Tap to pop-up keyboard then input the
The source unit will playback the audio in the USB
desired number.
device.
4. Tap to select Random is On / Off.
1 2 3 4 5. Tap to access to file list page.
6. Tap to zoom in the picture.
7. Tap to zoom out the picture.
8. Tap to playback next picture
USB file list:
1
5 6 7 8 9 10 11 12
1. Tap to back to home page.
2. Show the song’s album art picture.
3. Show the song’s ID3 information.
4. Tap to access to EQ settings page.
5. Tap to playback previoust track, press 2
and hold to activate the fast reverse, 1. Tap to show the music list.
press again to select fast reverse speed. 2. Tap to show the pictue list.
6. Tap to select play/ pause.
7. Tap to select repeat all / repeat 1 / Bluetooth Connect:
repeat directory. If the Bluetooth is not connected, press
8. Tap to select Random is On / Off. Reconnect the paired Phone or paring to pair
9. Tap to access to file list page. the new device.
10. Tap to playback previous folder.
11. Tap to playback next folder.
12. Tap to playback next track, press
and hold to activate the fast forward,
press again to select fast forward speed.
USB picture playback:
Bluetooth Pairing:
Pairing screen will be shown as below:
Turn on the Bluetooth of the Mobile phone/
Bluetooth device; you can see the "SOUND-
STREAM V2." Select the "SOUNDSTREAM V2" for
1 2 3 4 5 6 7 8 paring and connection.
24WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 25
Bluetooth Audio
Bluetooth Music Playback 1. Touch the icon to enter keypad screen.
Touch BT Audio icon to enter music 2. Using the keypad, touch 0-9,*,#, enter the phone
number you wish to dial. If you input
1 2
an incorrect number, touch the icon on the
keypad to delete the incorrect number.
3. Once the correct number appears on the
screen, touch the icon. To go to dialing
interface.
4. To end the call, touch the icon
on the screen.
3 4 5
1. Tap to back home page.
2. Tap to access to EQ settings page.
3. Play Previous song.
4. Tap to Play/Pause current song.
5. Play Next song.
Bluetooth Phone:
After the mobile Phone is connected with the
source unit via Bluetooth(HFP), the user can go
through the source unit.
Make a phone call. Touch the Phone icon in Main
Menu to go to BT Phone mode. Please note it needs
to connect the microphone for phone calls.
Once the phone and unit are connected successfully, 1 2 3 4
you’ll be able to make calls from the unit.
Touch to make a call.
1 Keypad Button
•Press to show the keyboard.
2 Mute Microphone Button
•Press to Microphone Mute or Un-Mute.
3 Hang-up Button
•Press to hang-up the calling.
4 Switch Button
•Press to switch call audio to phone or AV
receiver.
25WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 26
Headsets
Receive an incoming call BT Settings
If the Phone is connected with the source
unit via Bluetooth, when an incoming call,
below screen will be shown:
Auto Answer On /OFF, incoming call
auto answer.
Press to answer the incoming call. MIC Gain, Set MIC Gain is High/Mid/Low.
Press to reject the incoming call. Wireless Headset Integration
The wireless headset interface supports both OEM
Note : You can also manage calls through and aftermarket headsets and headphones. You can
your phone. pair up to two headsets or headphones for both the
rider and passenger. Additionally, you have the option
Recent (Calling Record) to select whether you want to hear only GPS naviga-
Check for dialed/answered/missed calls history. tion commands, only music, or both simultaneously.
Touch icon to enter calling record interface: Before using the wireless headset with any Bluetooth
devices for the first time, you will need to pair them
together. Audio Bluetooth headsets. This pairing
operation is only required once for any Bluetooth
device. The headset remains paired with the devices
and automatically reconnects to them when they are
within range. You will hear a high tone single
beep and a voice prompt when the headset connects
to the paired device automatically.
Phone Book
1. Turn on wireless headset.
2. Navigate: Home > Headset.
NOTE: Place headset in pairing mode before
selecting Pair Rider Headset.
3. Put Headset into pairing mode.
a. Touchscreen will display Pairing in Process with
Headset.
When your phone and unit are paired, the NOTE:Rider's headset should be paired first followed
unit can automatically reach contacts from by the passenger.
your phone and store them within the Select: Pair Rider Headset.
unit.(selected phones only)
26WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 27
Rally Mode
Rally Mode™ Music Sharing
Rally Mode™ Music Sharing allows you to broad-
cast your playlists to group riders. You can pair
with riders who have Rally Mode equipped head
units and accessories. An unlimited number of
users can pair with a principal broadcaster’s
stream.
V2 headunit indentify is DJ
Routing: Switch the media sound routing User can broadcast your playlists to group rider or
is Speaker or Headset. other accessories.
Call/Nav/Voice, Set Call/ Navigation/Voice
promotion routing is Speaker or Tap to select identify is DJ or Listener.
Headset.
Intercom Mode: When connect 2 headsets
device , user can switch the intercom
mode is On, then the rider and passenger
can start to intercom.
Headsets List: Tap to access headsets list page,
then can start search the device to connect.
Headsets List:
Tap DJ name item to pop-up the keypad, then
you can rename the device name for broad-
casting.
GPS Navigation Powered by iGo
Primo®
The NNG iGO Primo® GPS Navigation system
comes with maps and points of interest (P.O.I.) for
Tap to delete the disconnect the USA and Canada included. You can update
device. maps and P.O.I. information annually through
Naviextras.com. Uses OEM GPS Antenna if
Tap the connected device the disconnect it, tap
Equipped, Aftermarket Antenna Available.
again to reconnect it.
27WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 28
iGo map Operation
1 Warnings and safety information
3.Select the language and speaker used for
The navigation system helps you find your way voice guidance messages.Later you can
to your destination with the built-in GPS receiver. change it in Regional settings.
Soundstream V2 does not transmit your GPS
position; others cannot track you. Tap to continue.
It is important to look at the display only when it is
safe to do so. If you are the driver of the vehicle, we
recommend that you plan and review your route
before you start your journey. Plan the route
before your departure and stop if you need to
change the route. You must follow the traffic rules.
If you deviate from the planned route,
Soundstream V2 changes the instructions accord-
ingly.
2 Getting started 4. If needed, modify the time format and unit
settings. Later you can change them in Region-
Soundstream V2 is optimized for in-car use. You al settings . Tap to continue.
can use it easily by tapping the screen buttons
and the map with your fingertips.
2.1 Initial set-up
When using the navigation software for the
first time, an initial set-up process starts
automatically.
1. Select your preferred language, then
tap to confirm your selection. Later
you can change it in Regional settings .
5.If needed, modify the default route planning
options. Later you can change them in Route
Preferences.
Tap to continue.
2.The Configuration Wizard starts.
Tap to continue.
28WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 29
iGo map Operation
6.The initial set-up is now complete,
tap to enter the Navigation view.
2.2 Screen controls
The following sections describe the functionality and use of buttons, sliders, and other
screen controls in Soundstream V2.
2.2.1 Using the buttons and other controls
To operate Soundstream V2, tap the buttons on the touch screen.
Type Example Description Function
Opens a new screen where
Button you can set a parameter. Tap it once.
Displays the current value of a
field or setting where the value
Button can be changed. After the Tap it once.
with value change, the new value is shown
on the button.
Grab the list anywhere and slide
your finger up or down. Depend-
ing on the speed of sliding, the list
Shows multiple options. scrolls fast or slow, only a bit or till
List the end.Alternatively, move
between items in a list with the
arrows and tap the value that you
want to select.
Shows whether a feature is Tap it to turn the switch on or off.
Switch
enabled when there are only
two choices.
When a feature can be set to
different values in a range, Drag the handle to move the
Slider Epsilon Linux device shows an slider to its new position.Tap the
indicator on a gauge that slider where you want the handle
displays and sets the value. to appear.
Used to enter text and
numbers.
Virtual Each key is a touch screen button.
keyboard
29WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 30
iGo map Operation
The Navigation menu may contain several menu
items on one or more pages. Action Function
Switching to another
keyboard layout, for Tap then select the new
example from an
English keyboard to a keyboard layout from the list.
Greek keyboard
Tap to remove the
unnecessary character(s).
Correcting your entry Tap and hold the button to
You need to confirm selections or changes only if on the keyboard delete several characters or the
the application needs to be restarted, if it needs to entire input string.
perform a major reconfiguration, or if you are
about to lose some of your data or settings.
Otherwise, V2 saves your selections and applies Entering a space, for
the new settings without confirmation as soon as example between a Tap to button at the
you use the controls. first name and a family bottom centerof the screen.
name or in multiword
street names.
2.2.2 Using the cursor
You can select a map location in the following By default, when entering a
ways: text, the first character appears
in upper case while the rest of
By tapping the map when navigating the text is in lower case.
By tapping the map when you are asked to Entering upper and
confirm the destination at the end of a search. lower case letters. Tap to enter an upper case
letter or tap it twice to turn on
When a map location is selected, the cursor Caps Lock. Tap again to use
lower case letters.
( ) appears at the selected point on the
map.The location of the cursor can be used as the
destination of the route or a new Alert Point. You Tap to switch to a
Entering numbers and keyboard offering numbers
can also search for Places around it or add this symbols
location to your saved locations.You can also select and symbols.
some of the objects on the map. If you tap the map
at the icon of a Place or traffic event, the object is
selected, and you can get information about this
object or use it as a route point.
Finalizingthe keyboard Tap
2.2.3 Using the keyboard entry
You can type with your fingertips on the screen
keyboards and you can switch between various
keyboard layouts, for example English, Greek or
numerical. Only those keyboard buttons are active Hiding the keyboard Tap
that can be used to type a name that is available on
the map. The other keys are grayed out.
30WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 31
iGo map Operation
2.2.4 Using touch gestures 2.2.5 Manipulating the map
You usually need to tap the screen only once.
However, some useful features can be accessed If you tap the map anywhere during navigation, the
with other gestures. See the table below. map stops following the current position (the blue
arrow is not locked in a fix position on the screen
anymore) and control buttons appear to help you
Action Function modify the map view.
Tap and keep pressing the
following buttons to reach
extra functions:
Tap and hold the following
button on list and menu
screens to show the
Navigation view:
Tap and hold any of the You can perform the following actions on the map:
Tapping and following buttons on the
holding the Navigation view to rotate, Action Function
screen tilt, or scale the map /Buttons
continuously: The top section of the Navigation
view shows information about the
selected point (the
Tap and hold the following Checking
button on keyboard screens location cursor )
to quickly delete several information To restore the map view with your
position shown in the
characters:
middle, (the tap )
Tap and hold the following
buttons in long lists to scroll Moving the map Move the map in any direction: tap
pages continuously: by dragging and hold the map and move your
family name or finger towards the direction you
Drag the screen in the in multiword want to move the map.
following cases: street names.
To move the handle on a slider.
To scroll a list: grab the list
Change how much of the map is
anywhere and slide your finger
displayed on the screen. Epsilon Linux
Dragging up or down.
Zooming in device uses maps that let you examine
Depending on the speed of the
and out the locations at various zoom levels,
sliding, the list scrolls faster or
always with optimized content. It
slower, only a bit or till the end.
always displays street names and other
To move the map in map
text with the same font size, never
browsing mode: grab the map,
upside-down, and you only see the
and move it in the desired
streets and objects that you need. Map
direction.
scaling has a limit in 3D map view
mode. If you zoom out further, the
Use pinch zoom on the map switches to 2D view mode. Tap
Hiding the
Navigation view to zoom in once to modify the view in a large step,
keyboard
and out by moving two or tap and hold the button to modify it
fingers in a pinch gesture. continuously and smoothly.
31WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 32
iGo map Operation
You can perform the following actions on the map: 2.3 Navigation view
The navigation view is the main screen of Epsilon
Action Function Linux device that shows the planned route on a map.
/Buttons Epsilon Linux device works with digital maps which
are not simply the computerized versions of tradition-
Tilting up Change the vertical view angle of al paper maps. Similarly to paper road maps, the 2D
and down the map in 3D mode. Tap once to mode of digital maps shows you streets and roads.
modify the view in a large step, or Elevation is also illustrated in color. The navigation
tap and hold the button to modify view displays the following screen buttons, data
it continuously and smoothly. fields, and route information on the map during
navigation:
Rotating left Changes the horizontal view angle
and right of the map. Tap once to modify the
view in a large step, or tap and hold
the button to modify it continuous-
ly and smoothly.
Changing Switch between the 3D perspective,
2D, 3D, or 2D 2D Heading up, and 2D North up
North up map view modes. In Heading up
views mode the map is rotated so its top
always points in the current driving
direction. This is the default orienta-
tion in 3D map view mode. In North
up mode, the map faces North.
Checking the The direction of the compass shows
compass North.
Selecting Open a list of additional features like
additional saving a location, or searching for
options Places around the cursor.
Note! Some buttons, fields, or icons may
not be available in your product version.
Selecting a Select the cursor location as a new
destination destination. The route is automati-
cally calculated.
32WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 33
iGo map Operation
Number Name Description
1. Current
position
marker
2. The dot near the arrow shows the GPS position as perceived by the GPS
GPS position
receiver.
3. Planned route The planned route is displayed as an orange line.
Three data fields show the following information:
The estimated time of the arrival at the destination.
The remaining time of the trip.
The remaining distance to the destination.
4. Data fields Tap this area to access the Trip Computer screen with additional information
about the current trip on a dashboard. You can change the default values in
Settings or by tapping and holding the area where the data fields appear. If
you have not selected a destination, you can see your heading instead of the
three data fields.
Next turn It shows the type of the next maneuver and its distance.
5. preview
6. Second next
turn preview It shows the type of the second next maneuver if it is near the first one.
7. Next street It displays the name of the next street. If you have not selected a route
destination, you can see nearby house numbers, if they are available.
8. Home Tap to return to the Home screen of your infotainment system.
9. Lane On multi-lane roads, it shows the lanes ahead and their directions. The
information highlighted arrows represent the lanes and direction you need to take.
10. Alert point It shows the type of the alert points when approaching a road safety camera
warning or other Alert Points like school zones or railroad crossings. You must make
sure that using this feature is legal in the country where you intend to use it.
11. Speed limit It shows the current speed and the speed limit when speeding
warning
12. Signpost It shows the available destinations and the road numbers.
13. Freeway By tapping it, you can check the details of the next few service stations (gas
services stations, restaurants) when traveling on a freeway.
14. Parking around It appears near the destination. By tapping it, you can check the available
destination parking facilities around your destination.
15. Destination It appears near the destination. By tapping it, you can check the trip summa-
menu ry, find Places around your final destination, save the current location, or
suspend the navigation.
33WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 34
iGo map Operation
16. Navigation By tapping it, you can open the Navigation menu, where you can reach other
menu parts of Epsilon Linux device.
17. 3D objects They display hills, mountains, roads, landmarks, and buildings in 3D.
18. Street name It shows the current street name. By tapping it, you can open the Where Am I
screen.
2.3.4 The planned route
2.3.1 Streets and roads The planned route is the currently navigated route.
V2 device shows the streets similarly to paper road Whenever the destination is set, the route is active
maps. Their width and colors correspond to their until you delete it, reach your destination or suspend
importance; you can easily tell a freeway from a small navigation. Epsilon Linux device displays the route in
street. the following ways:
2.3.2 GPS position markers Symbol Description
When your GPS position is available, Epsilon Linux /Name
device marks your current position. By default, this
marker is a blue arrow. The dot near the arrow shows It is your current position displayed
the GPS position as perceived by the GPS on the map.
receiver.When on-road navigation is selected, the If a vehicle is selected for route
current position marker may not show your exact GPS calculation and roads are near, the
position and heading. If roads are near, it is aligned to arrow jumps to the nearest road.
Current GPS Normally, if GPS position is available,
the nearest road to eliminate GPS position errors, and position and
the direction of the icon is aligned to the direction of the route starts from the current
starting position. If there is no valid GPS
the road. If you select off-road navigation, the current point
position marker is at your exact GPS position. The position, Epsilon Linux device uses
direction of the icon shows your current heading. the last known position as the
starting point.
2.3.3 Turn preview and next street
When navigating a route, the top section of the It is an intermediate destination of
Navigation view shows information about the next the route before reaching the final
route event (maneuver) and the next street or the destination.
next town. Waypoint
(intermedi-
ate destina-
tion)
It is the final destination of the route.
Destination
(end point)
There is a field in the top left corner displaying the Route color The route always stands out with its
next maneuver. Both the type of the maneuver (turn, color on the map, both in daytime
traffic circle, exiting freeway, and so on) and its and night color modes.
distance from the current position are displayed. A You can choose whether you want to use
smaller icon shows the type of the second next Streets and or avoid certain road types. However,
maneuver if it is near the first one. Otherwise, only the roads that when Epsilon Linux device cannot avoid
next maneuver is displayed. Tap the icon of the actual are exclud- such roads, the route includes them and
maneuver to open the Itinerary screen. ed from the shows them in a color that is different
navigation from the route color.
34WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 35
iGo map Operation
2.3.5 Maneuver icons 2.3.6 Lane information
During navigation the next maneuver is displayed in When navigating on multi-lane roads, it is important
the top left corner. Most of the maneuver icons are to take the appropriate lane in order to follow the
intuitive. The following table lists some of the planned route. If lane information is available in the
frequently shown route events: map data, Epsilon Linux device displays the lanes and
their directions using small arrows at the bottom of
Icon Function the map. Highlighted arrows represent the lanes and
the direction you need to take.
Turn left.
Turn right.
Turn back.
Bear right.
Turn sharp left.
2.3.7 Signposts
Keep left.
If necessary information is available, Epsilon Linux
device displays signposts at the top of the map. The
Continue straight in the intersection. color and style of the signposts are similar to the real
ones you can see above roads or by roadsides. They
Enter the traffic circle and take the first exit (next show the available destinations and the road
maneuver). numbers. All signposts look similar when cruising
Enter the traffic circle (second next maneuver). (when there is no planned route). During navigation
only the signpost that points to the lane(s) to be
taken is highlighted; all the others are darker.If you
Enter the freeway. want to hide the currently displayed signposts, tap
any of them and the normal Navigation view returns
Exit the freeway. until new signpost information is received.
Board the ferry.
Leave the ferry.
Approaching a waypoint on the right.
Approaching the destination.
You can modify the signpost settings .
2.3.8 Freeway services
When you are driving on a freeway, the button
appears at the top right corner of the Navigation
view. Tap it to open a panel with the details of the
next few service stations (gas stations, restaurants).
35WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 36
iGo map Operation
Tap any of them to display the exit area on the map.
You can now easily add this service station as a
waypoint to your route if necessary. If you want to
display other types of Places at the next few service
stations, you can change the icons in
2.3.9 3D object types You can see the following menu options when you
Epsilon Linux device supports the following 3D object are navigating without a planned route:
types:
Button Function
Type Description
Select your destination by entering an
Epsilon Linux device displays 3D address or its coordinates, or by selecting
hills and mountains in the Naviga- a Place, a Saved Location, or a Saved
3D terrain tion view, and illustrates them by Route. You can also look up your recent
coloring and shading on the 2D destinations from the History.
map. Build your route from one or more route
points. You can also plan a route
independently of your current GPS
Elevated roads Elevated roads are complex position by setting a new starting point.
intersections and vertically isolated
roads (such as overpasses or Access additional options and check
bridges) displayed in 3D. navigation-related information.
Customize the way the navigation
3D landmarks Landmarks are 3D representations of software works.
prominent or well-known objects.
You can access the latest free map or
software updates here.
3D buildings 3D buildings are block representa-
tions of full town building data The About section pro you with product
containing actual building sizes and information. Read the Software and
positions on the map. Database End User License Agreement, or
check the map and other contents of the
2.4 Navigation menu application. You can also access program
On the Navigation view, tap to open the usage statistics.
Navigation menu.
36WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 37
iGo map Operation
With a planned route, the following menu options are
also available: Button Function
Button Function Check those notifications that contain
important information but do not require
immediate action from the users. If there
Add an intermediate destination to your are no notifications, this icon is not
route. displayed.
See route alternatives to avoid parts of the The Menu button appears when the
route, or to avoid a specific road from your Navigation view is displayed. Tap it to
planned route. open the Navigation menu. .
View the route in its full length on the
map and check route parameters and r The More button appears on the screen
to display additional features. Tap it to
oute alternatives. Tap to access open the list of additional features on
additional options, like Simulation or certain screens.
Route Preferences.
Tap the Back button to return to the
Delete your route. previous screen. You can also press and
hold this button to quickly return to the
Navigation view from any other screen.
Delete the next waypoint or the whole
route. It is displayed if there is a multipoint
route. 3 Using the navigation
By default, V2 device calculates routes using the road
In the navigation menu, you have the following network of the maps provided with the product. You
additional options: can select the destination and start navigating to it
right away (normal navigation) if you need a route for
Button Function immediate navigation. You can also plan a route
independently of your current GPS position even
Open the Saved Locations screen where without GPS reception. To achieve this, you need to
you can save a location as a favorite set a new starting point in the Multipoint Route
destination or edit a saved location. menu. It also suspends guidance so that the route is
not recalculated when a new position is received. See
Switch to 2D ( ), 2D North page 50. You can plan routes with multiple destina-
tions by selecting a first and a second destination and
up ( ) view or back to 3D mode. adding it to your route. You can add as many destina-
tions to your route as you like. You can also use
Suspend navigation. Epsilon Linux device for off-road navigation.
Resume navigation.
Access the User profiles menu where you
can create new profiles or edit the
existing ones. If several drivers are using
the navigation system, they can create
their own profiles with their own settings.
37WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 38
iGo map Operation
3.1 Selecting a destination 4. (optional) To search in a different area, tap the
You can choose your destination by selecting one of input field with the search area, and start entering the
the following options: name of the new search area on the keyboard.
* Using combined search to search among different
destination types at once.
* Entering a full address or a part of an address, for
example a street name without a house number
* Selecting a Place as your destination.
*Selecting a previously saved location as your
destination.
*Selecting a location from the History of previously
used destinations.
*Selecting a previously saved route.
*Entering the coordinate of the destination. You only need to enter a few letters to get a result.
*Selecting a location on the map. The most likely result appears below the input field as
*Planning a multipoint route. you enter new letters.
a. If the new search area is in a different country or
state, start entering the country/state and the town.
3.1.1 Using combined search
There are several ways to select your destination. You b. Tap to see the whole list of the
can initiate a separate search for addresses, Places, matching results.
saved locations, or recent destinations, but the fastest
way to search for any of these is to use combined 5. With the proper search area displayed, start
search. Perform the following steps to use combined entering the name, address, or category of the
search: destination you are looking for.
1. Tap on the Navigation view to access the
Navigation menu.
2. Tap .
3. Tap . You can see the input field
at the top of the screen. Right next to it you can see 6. Tap to switch to the result screen. You
the search area, the town around which the search is can see all the results in the list, regardless of their
carried out. The default search area is the area where type. Addresses, Places, Place categories, Saved
you are located. For a local search, skip the next step. locations, and recent destinations are mixed in one
list. You can immediately select the result you want to
use as your destination or narrow the list of results for
only one type (for example, Places).
38WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 39
iGo map Operation
9. Check the settings for road types and change them
7. If necessary, tap on the right side of the if necessary.
list and then tap the corresponding button to narrow
the list of search results by type (the number on the Tap to enable or avoid freeways, tap for
related icon shows the number of the matching
results): roads with Period Charge or Per-use Toll, tap for
* Tap to see the list of recent destinations
ferries, or tap for carpool lanes.
with a matching name or address.
* Tap to see the list of your saved locations
with a matching name.
*Tap to see the list of matching addresses.
*Tap to see the list of matching Place category
names. Scroll the list and select one of the categories.
You get the list of Places in that category ordered by 10. Tap to confirm the destination,
their distance from your current position.
or tap to select a different destination.
Tap to see the list of matching Places ordered
by their distance from your current location. 11. The route is calculated and the map appears
(optional) If your product contains Places from showing the entire route, where you can check route
different data providers, you can further narrow the
list by showing the results from one provider only. information and route alternatives. Tap to
Look for the provider logos.
Tap one of them to see Places from that provider. modify the route parameters, or tap to
start your journey.
Note: To search for an intersection in the combined
search, enter the names of the streets connect-
ed by the '&' sign. You do not need to use
spaces before and after the separator charac-
ter. For example you can find the intersection
of Collins Street and Douglas Avenue by
entering strings, like "Collins St & Douglas Ave",
"Collins & Douglas", "Col&Doug", etc. The more
precise the input string is, the fewer false
results are expected. If you enter "Collins St&",
you get all the intersections of Collins Street
and you can select the appropriate one from
the result list. one type (for example, Places).
8. Once the destination is selected, a full screen map
appears with the selected point in the middle. If
necessary, tap the map somewhere else to modify
the destination. The cursor ( ) appears in the
new location.
39WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 40
iGo map Operation
3.1.2 Selecting an address b. Tap to open the list of results and
If you know at least a part of the address, this is the select one country from the list.
quickest way to select your destination. Using the
same screen, you can find an address by entering 4. If needed, select a new city.
the following information:
*The exact address, including the house number.
*The address starting with the street name a. Tap the City or ZIP code field.
*The center of a town b. (optional) In the Select City or ZIP code screen,
*The midpoint of a street, you can immediately select a city from the list of
*An intersection, suggestions.
*Any of the above, starting the search with the ZIP
code,
3.1.2.1 Entering an address with states
To enter an address as the destination, follow these
steps:
1.Tap on the Navigation viewto access the
Navigation menu
c. Otherwise, start entering the first few letters of the
2.Tap and . city on the keyboard. The names that match the
string appear in a list.
3. By default, the Epsilon Linux device proposes the d.To open this list, tap and select the
country and state where you are or in case there is city.
no valid GPS position, the country and state of the
last known position. If needed, change the country.
tap
a. In the Select Country screen, you can immediately
select a country from the list below the input field or
tap the button and start entering
the first few letters of the country on the keyboard. If
you select a country without a state, you can search
for a town in all its states.
40WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 41
iGo map Operation
5. Enter the street name. 7.Check the settings for road types and change
a. Tap the Street field. b. (optional) On the Select them if necessary.
Street screen, you can immediately select a street
from the list of suggestions. Tap to enable or avoid freeways, tap for
roads with Period Charge or Per-use Toll, tap for
ferries, or tap for carpool lanes.
c. Otherwise, start entering the street name on the
keyboard, the names that match the string appear in
a list.
d.Tap to open the list of results. Select
the street from the list.
8. Tap to confirm the destination,
or tap to select a different destination.
9. The route is calculated and the map appears
showing the entire route, where you can check route
information and route alternatives. Tap to
modify the route parameters, or tap to
start your journey.
6. A full screen map appears with the selected point
in the middle. If necessary, tap the map somewhere
else to modify the destination. The cursor ( )
appears at the new location. 3.1.2.2 Entering an address starting with the street
name
After you have selected the country and state, you
can leave the city or ZIP code field empty and start
the search with the street name. This way you can
search in all streets of a state. If you select the country
without a state, this function cannot work.
41WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 42
iGo map Operation
1. Tap on the Navigation view to access the
Navigation menu.
2. Tap and .
5. Enter the street name.
a. Tap the Street field.
a. In the Select Country screen, you can immediately b. (optional) On the Select Street screen, you can
select a country from the list below the input field or immediately select a street from the list of sugges-
tions.
tap the button and start entering the
first few letters of the country on the keyboard.
b.Tap to open the list of results and select
one country from the list.
4. If needed, select a new city. a. Tap the City or ZIP
code field. b. (optional) In the Select City or ZIP code
screen, you can immediately select a city from the list
of suggestions. c. Otherwise, start entering the street name on the
keyboard, the names that match the string appear in
a list.
d. Tap to open the list of results. Select the
street from the list.
c. Otherwise, start entering the first few letters of the
city on the keyboard. The names that match the
string appear in a list.
d. To open this list, tap and select the city.
42WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 43
iGo map Operation
6. A full screen map appears with the selected point in 3.1.2.3 Selecting a town center
the middle. If necessary, tap the map somewhere else The town center is not the geometric center of the
town but an arbitrary point the map creators have
to modify the destination. The cursor ( )appears chosen. In towns and villages, it is usually the most
at the new location. important intersection and in larger towns, it is one of
the important intersections.
7. Check the settings for road types and change them
if necessary.
1. Go to , , and modify the country
and state as described earlier, if necessary.
Tap to enable or avoid freeways, tap for
roads with Period Charge or Per-use Toll, tap for
ferries, or tap for carpool lanes.
c. Otherwise, start entering the first few letters of the
town. The names that match the string appear in a
list.
d. To open the list, tap and select the town.
8. Tap to confirm the destination,
or tap to select a different destination.
9. The route is calculated and the map appears
showing the entire route, where you can check route
information and route alternatives. Tap to
modify the route parameters, or tap to
start your journey. 3. Tap . This way the center of the
displayed town becomes the destination of the route.
3.1.2.4 Selecting the midpoint of a street
To navigate to the midpoint of a street without
entering the house number, perform the following
steps:
43WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 44
iGo map Operation
3.1.2.5 Selecting an intersection in a town
1. Go to , , , and select the country and To navigate to an intersection, perform the following
town as described earlier. The Select Street screen steps:
appears.
1. Go to , , and select the country and city
2. Enter the street name by performing the following
steps: as described earlier.
a. Tap the Street name field. 2. Enter the street name by performing the following
b. (optional) On the Select Street screen, you can steps: a. Tap the Street name field. b. (optional) On the
immediately select a street from the list of sugges- Select Street screen, you can immediately select a
tions. street from the list of suggestions.
c. Otherwise, start entering the street name on the
c. Otherwise, start entering the street name on the keyboard. The names that match the string appear in
keyboard. The names that match the string appear in a list.
a list.
d.d. Tap to open the list of results. Select
d.d. Tap to open the list of results. Select the street from the list.
the street from the list.
3. Instead of entering the house number,
tap . The midpoint of the street is
selected as the destination.
44WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 45
iGo map Operation
3. Tap the House number or crossing street field and 3.1.3 Selecting a Place of Interest
browse the list of crossing streets or start entering the You can search for Places of Interest (Places) in the
street name in the field. Select one from the list. menu. Using the same screen, you can find a Place by
selecting one of the following options:
*Finding frequently searched types of Places with the
Quick search categories
* Searching for a Place by its name,
*Searching for a Place by its category,
*In case of emergency, you can also find help nearby,
3.1.3.1 Using Quick search categories
The Quick search feature helps you quickly find the
3.1.2.6 Using the ZIP code to select a destina- most frequently selected types of Places. Perform the
tion following steps:
You can also select any kind of destination by
entering the ZIP code instead of the city name. To 1. Tap on the Navigation view to access the
select the ZIP code, perform the following steps: Navigation menu.
2. Tap and .
1. Go to , , and modify the country and
state as described earlier.
2. Tap the Town or ZIP code field. 3. Enter the ZIP code
by performing the following steps:
a. Tap to open the numeric keypad.
b. Start entering the ZIP code.
c. Tap to open the list of results. The following Quick search categories appear: .
: If a planned route exists, gasstations
d. Find the place you need. are searched along the route.
: If a planned route exists, accommo-
dation is searched around the
destination.
: If a planned route exists, restaurants
are searched along the route.
: If a planned route exists, parking
lots are searched around the
destination.
If there is no planned route (destination is not
selected), the search is carried out around the current
position. If the current position is not available either
(no GPS signal), places are searched around the last
known position.
4. Continue the search as described previously .
45WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 46
iGo map Operation
3. Tap any of the quick search buttons to get an
instant list of Places.
10. Tap to confirm the destination.
4. The Places in the list can be ordered by their You can also select a nearby point on the map
distance from the current or last known position, from
the destination, or by the length of the necessary or tap to select a different destination.
detour. If you need to reorder the list, tap . 11. The route is calculated and the map appears
showing the entire route, where you can check route
To filter the list of results by providers, tap and
information and route alternatives. Tap to
then the provider logo on the right side of the screen.
modify the route parameters, or tap to
5. (optional) If needed, tap to further start your journey.
filter the list of results.
6. Browse the list and tap one of the list items. A full
screen map appears with the selected point in the
middle. The name and address of the Place is
displayed at the top of the screen.
7. Tap to see the details of the selected Place,
or to save the location. If there is a telephone number
saved for this Place, you can make a call to that
number by tapping the green button at the bottom. 3.1.3.2 Searching by category
To search for Places by their categories and subcate-
8. If necessary, tap the map somewhere else to gories, perform the following steps:
modify the destination. The cursor ( ) appears 1. Tap on the Navigation view to access the
at the new location. Navigation menu.
9. Check the settings for road types and change them 2. Tap and .
if necessary.
3. Tap
Tap to enable or avoid freeways, tap for 4.Select the area around which you would like to
roads with Period Charge or Per-use Toll, tap for search for the Place by tapping .
By default, the search area is around the current
ferries, or tap for carpool lanes. position (or if it is not available, around the last known
position). In this case, the following result list is
ordered by the distance from this position.
46WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 47
iGo map Operation
Tap to search along the planned
route, and not around a given point. This is useful
when you search for a later stopover that results
in a minimal detour only, such as searching for
upcoming gas stations or restaurants. (The result
list is ordered by the length of the necessary
detour.)
7. You can turn the Category View off at any level to
Tap to search for a place around list all Places around the selected location or along
the destination of the planned route. (The result the route.
list is ordered by the distance from the destina-
tion.)
Tap to search for a place within a
selected town. (The result list is ordered by the
distance from the centerof the selected town.)
8. (optional) The Places in the list can be ordered by
the following criteria:
*Name
*Their distance from the current or last known
position
*Their distance from the selected town
5.(optional) If you have selected , *Their distance from the destination
*The length of the necessary detour.
select the town to search in.
Tap to reorder the list.
To filter the list of results by providers, tap and
then the provider logo on the right side of the screen.
9. Browse the list and tap one of the list items. A full
screen map appears with the selected point in the
middle. The name and address of the Place is
displayed at the top of the screen.
6. Select one of the main Place categories (for
example, Accommodation), then browse the subcat- 10. The process continues the same way as in case of
egories (for example, Hotel or Motel) to find your any other search for Places.
destination.
47WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 48
iGo map Operation
3.1.3.3 Searching by name 5. (optional) If you have selected , select the town to
To search for a Place by name, browse the various Place
categories, or use the mixture of the two search types, search in . .
perform the following steps:
1. Tap on the Navigation view to access
the Navigation menu.
2. Tap and . .
3. Tap to open the Search By Name
or Category window.
4. Select the area around which you would like to
search for the Place. By default, the search area is You can search for the name of a Place in all catego-
around the current position (or if it is not available, ries by performing the following steps: .
around the last known position). In this case, the
result list is ordered by the distance from this position. 1. Tap . Using the keyboard, start
entering the name of the Place or browse in the
Tap to select one of the following search categories. .
areas:
Tap to search for a place within a
selected town. (The result list is ordered by the
distance from the centerof the selected town.)
Tap to search for a place around
the destination of the planned route. (The result
list is ordered by the distance from the destina-
tion.) 2. After entering a few letters, tap to
open the list of Places or Place categories with
Tap to search along the planned names containing the entered character
route, and not around a given position. This is sequence.
useful when you search for a later stopover that
results in a minimal detour only, such as
searching for upcoming gas stations s or
restaurants. (The result list is ordered by the
length of the necessary detour.)
3. Browse the list, if necessary, and tap the desired
list item. A full screen map appears with the
selected point in the middle. The name and
address of the Place is displayed at the top of the
screen.
4. The process continues the same way as in case
of any other Places search.
48WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 49
iGo map Operation
3.1.3.4 Finding help nearby 4. (optional) The Places in the list can be ordered
To quickly search for nearby assistance, perform the by the following criteria:
following steps: * By their distance from the current or last known
position
* By name.
1. Tap on the Navigation view to access
Tap to reorder the list.
the Navigation menu.
5. Browse the list and tap one of the list items. A
2. Tap and . . full screen map appears with the selected point
in the middle. The name and address of the Place
is displayed at the top of the screen.
6. The process continues the same way as in case
of any other Places search.
3.1.4 Selecting a Saved Location
To select a location that you have already saved perform
the following steps:
1. Tap on the Navigation view to access
Places in the following pre-set search categories the Navigation menu.
can be searched for around the current position
(or around the last known position if the current 2. Tap and . .
position is not available):
3. The list of saved locations is displayed. It contains
: Car repair and roadside two pre-set categories: Home and Work. .
assistance services the route.
: Medical and emergency
services
: Police stations
: Gasstations 4. Tap the location that you want to set as your
destination. If necessary, browse the list to see
more results.
3. Tap any of the quick search buttons to get an
instant list of those types of Places. 5. (optional) If needed, tap to enable the
editing option so that you can rename the saved
locations or delete any of them.
6. After you have selected a saved location as the
destination, a full screen map appears with the
selected point in the middle.
7. If necessary, tap the map somewhere else to
modify the destination. The cursor ( )
appears in the new location.
49WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 50
iGo map Operation
8. Check the settings for road types and change them if
necessary.
1. Tap on the Navigation view to access
Tap to enable or avoid freeways, tap for the Navigation menu.
roads with Period Charge or Per-use Toll, tap for 2. Tap . Two of the Smart History Items are
ferries, or tap for carpool lanes. displayed in the New Route to... screen for easy
access. You can select one of them as your destina-
tion. .
9. Tap to confirm the destination.
You can also select a nearby point on the map
3. To open all the history items, tap . The
or tap to select a different destination.
list of recent destinations appears. The list begins
10. The route is calculated and the map appears with the three most likely destinations that are
showing the entire route, where you can check route selected based on your previous routes (Smart
History). The rest of the destinations are ordered by
information and route alternatives. Tap to the time they were last selected. If necessary, scroll
the list to see earlier destinations.
modify the route parameters, or tap to 4. Select a destination from the list.
start your journey. 5. A full screen map appears with the selected point
in the middle. If necessary, tap the map somewhere
else to modify the destination. The cursor ( )
appears at the new location.
6. Check the settings for road types and change
them if necessary.
Tap to enable or avoid freeways, tap for
3.1.5 Selecting a History item roads with Period Charge or Per-use Toll, tap for
The destinations that you have used earlier appear in
the History list. Smart History offers these locations ferries, or tap for carpool lanes.
from your previous destinations, using parameters
like the current time of day, the day of week, and the
current location. The more you use the navigation
software, the better it can guess your desired destina-
tion. To select a History item, perform the following
steps:
50WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 51
iGo map Operation
7. Tap to confirm the destination. 3. The list of saved routes appears. If necessary, scroll
You can also select a nearby point on the map the list to see earlier routes.
4. Select a route and the Multipoint Route screen
or tap to select a different destination. appears. If necessary, modify the saved route.
8. The route is calculated and the map appears Otherwise, tap .
showing the entire route, where you can check route
5. The route is calculated and the map appears
information and route alternatives. Tap to showing the entire route, where you can check route
modify the route parameters, or tap to information and route alternatives. Tap to
start your journey.
modify the route parameters, or tap to
start your journey.
3.1.6 Selecting a saved route
The routes that you have saved earlier appear in a list.
To select a previous route, perform the following 3.1.7 Entering coordinates
steps: To select a destination by entering its coordinates,
perform the following steps:
1. Tap on the Navigation view to access
1. Tap on the Navigation view to access
the Navigation menu.
the Navigation menu.
2. Tap . .
2. Tap . .
3. You can enter the latitude and longitude values in
any of the following formats: decimal degrees,
degrees and decimal minutes, or degrees, minute
and decimal seconds. Tap
51WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 52
iGo map Operation
6. Tap to confirm the destination.
You can also select a nearby point on the map
or tap to select a different destination.
7. The route is calculated and the map appears
showing the entire route, where you can check route
information and route alternatives. Tap to
Note:
(optional) If necessary, tap then and modify the route parameters, or tap to
start your journey.
enter the coordinate in UTM format.
4. A full screen map appears with the selected point in 3.1.8 Selecting a location on the map
the middle. If necessary, tap the map somewhere else To select a map location, perform the following steps:
to modify the destination. 1. Locate your destination on the map. Move and
scale the map as necessary.
The cursor ( ) appears at the new location.
5. Check the settings for road types and change them
if necessary.
Tap to enable or avoid freeways, tap for
roads with Period Charge or Per-use Toll, tap for
ferries, or tap for carpool lanes.
2. Tap the location that you want to select as your
destination. The cursor ( ) appears there.
3. (optional) If needed, tap to list
the Places near the selected point or to save this
location.
52WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 53
iGo map Operation
Note.
4. Tap to select the destination.
If you already have a planned route, tap and
5. The New Route to... screen appears, where you can
to add the selected location to your select the destination of the route the same way as
route. described in the previous sections.
4. Tap to confirm the destination,
5. The route is calculated and the map appears
showing the entire route, where you can check route
information and route alternatives. Tap to
modify the route parameters, or tap to
start your journey. 6. When the selected location appears on the map,
tap and the list returns. If needed,
you can add further intermediate destinations.
3.1.9 Planning a Multipoint Route
To build your route destination-by-destination, 7. To add more route points, tap or
perform the following steps:
tap to change the final destination.
1. Tap on the Navigation view to access The Add to Route... menu appears again, where you
the Navigation menu. can select the new route point the same way as you
have set the destination before.
2. Tap .
8. (optional) Tap to optimize the whole
route or the order of waypoints. You can also delete
all the destinations.
9. When you have added all the route points,
tap and the planned route
is automatically calculated.
3. There is only one line in the list of route points, the
starting point of the route, which is normally the
current GPS position.
53WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 54
iGo map Operation
3.2 Checking route information and alternatives
To get a map overview of the planned route and By tapping , your can see a list
check different parameters of the planned route,
perform the following steps: of route alternatives and select the most suitable
route.
1. Tap on the Navigation view to access
the Navigation menu.
2. Tap .
The planned route is displayed in its full length on the
map with the following additional information:
*The total length of route
*The total time of route.
3. Tap on the Route Summary screen to carry
out additional actions, for example edit your route
preferences or display the itinerary.
3.3 Editing the route
When navigation has already started, there are several
ways to modify the planned route. You have the
following options:
*Setting a new starting point,
By tapping , you can check detailed * Adding an additional destination
*Modifying the list of destinations,
information about the route. If you tap on *Saving the planned route,
*Deleting the planned route,
the right side of the screen, you can narrow the route *Selecting a route alternative when planning the
information, for example to show only freeway route,
sections or toll roads. *Selecting a route alternative for an existing route,
* Pausing guidance.
3.3.1 Setting a new starting point
For normal navigation, all routes are calculated from
the current position. You can pause navigation to
check future routes, simulate them or see their length
in time and distance. Then you can set the starting
point of the route to a location other than the current
GPS position.
1. Tap on the Navigation view to access
the Navigation menu.
2. Tap .
54WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 55
iGo map Operation
3.2 Checking route information and alternatives
To get a map overview of the planned route and By tapping , your can see a list
check different parameters of the planned route,
perform the following steps: of route alternatives and select the most suitable
route.
1. Tap on the Navigation view to access
the Navigation menu.
2. Tap .
The planned route is displayed in its full length on the
map with the following additional information:
*The total length of route
*The total time of route.
3. Tap on the Route Summary screen to carry
out additional actions, for example edit your route
preferences or display the itinerary.
3.3 Editing the route
When navigation has already started, there are several
ways to modify the planned route. You have the
following options:
*Setting a new starting point,
By tapping , you can check detailed * Adding an additional destination
*Modifying the list of destinations,
information about the route. If you tap on *Saving the planned route,
*Deleting the planned route,
the right side of the screen, you can narrow the route *Selecting a route alternative when planning the
information, for example to show only freeway route,
sections or toll roads. *Selecting a route alternative for an existing route,
* Pausing guidance.
3.3.1 Setting a new starting point
For normal navigation, all routes are calculated from
the current position. You can pause navigation to
check future routes, simulate them or see their length
in time and distance. Then you can set the starting
point of the route to a location other than the current
GPS position.
1. Tap on the Navigation view to access
the Navigation menu.
2. Tap .
55WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 56
iGo map Operation
3.3.2 Adding an additional destination
If you already have a planned route and you select a
new destination as described in the above sections,
the route to the previous destination is deleted and a
new route is calculated. To add a new intermediate
destination to the planned route, perform one of the
following actions:
* Tap the map anywhere to browse it.
3. The first line from the bottom is the start of the After selecting the location on the map, tap and
route, normally the current GPS position. to add the selected location to your route as an
intermediate destination. The other destinations of
Tap , select , and the route remain intact.
confirm your action at the warning message. * Tap on the Navigation view and
tap . Add a destination to your route as
described.
3.3.3 Modifying the list of destinations
To edit your route, perform the following steps:
1. Tap on the Navigation view to access
4. The Change Start to... screen appears. Select the the Navigation menu.
starting point of the route the same way you select a
destination. 2. In the Navigation menu ,Tap .
5. You can see the new starting point on the map. You have the following options on this screen:
Tap and the Multipoint Route screen appears where
you can continue adding a destination to your route. *Tap to delete all the destinations, or
optimize the waypoints or the route.
6. Tap to continue. The route will be *Tap the name of the intermediate destination to
saved with the starting point that you have just set. move it up or down in the list, to save the location, or
You can use the saved route later to plan a route. to delete it from the list.
*If you have a route with at least one intermediate
destination, you can delete the waypoint from the list
r
ight from the Main menu. Tap , then confirm
the deletion.
56WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 57
iGo map Operation
3.3.4 Saving the planned route 3.3.5 Deleting the planned route
To save the planned route, perform the following You have the following two options to delete the
steps: navigated route:
1. Select a destination as described earlier and *If you already have a planned route and you select a
new destination as described in the above sections,
tap the route to the previous destination is automatically
deleted and a new route is calculated.
* In the Navigation menu, tap or .
If there are no waypoints, the planned route is
deleted after a confirmation. If you have waypoints,
you can choose to delete the whole route, or only the
next waypoint.
3.3.6 Selecting a route alternative when planning the
2. Tap and . route
To select from different route alternatives or change
the route planning method after you have selected a
3. Type in a name and tap new destination, perform the following steps:
1. Select a destination as explained earlier, and go
to the route confirmation screen.
4. The route is saved and it is available in
2. Tap
3. You can see the basic details of route alterna-
tives. Tap any of them to see it on the map.
By selecting a previously saved route, V2 device
recalculates the route using the saved destination
and/or the waypoints.
575WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 58
iGo map Operation
4. To view more suggestions, tap and 4. If there are more than a few suggestions, you
scroll down for other alternative routes with can tap and scroll down for routes.
different route planning methods.
5. Select one of the route alternatives and
5. Select one of the route alternatives and
tap to return to the previous screen. V2
tap to return to the previous screen.
device recalculates the route. Tap to V2 device replaces the original route.
start your journey. The orange line now shows the Tap to start your journey. The orange
new planned route. line now shows the new planned route.
3.3.8 Setting a detour
1. Tap on the Navigation view to access
the Navigation menu.
1. Tap on the Navigation view to access
2. You can access the list of route alternatives the Navigation menu.
from the Navigation menu in one of the following
ways: 2.In the Navigation menu, tap .
* Tap and . You can set up a detour for your route in the
following ways:
* Tap and . Tap to open a list of special sections of the
planned route such as stretches of freeway,
3. You can see the basic details of a few route toll road or ferry trips. Tap any of these items
alternatives. Tap any of them to see it on the map. on the itinerary to avoid a special section.
Tap to open the full list of roads on the
planned route. Tap any of these items on the
itinerary to avoid that specific road.
Tap to avoid a part of the planned route
that is right ahead of you on the itinerary.
You can set the distance for which you want
to avoid the road ahead.
If there are suitable alternatives calculated with
the route planning method that is selected in Tap to delete all detours that you have set
Route preferences , they are shown on top of the up for the planned route,
list. Routes with other route planning methods
are shown at the bottom of the list.
58WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 59
iGo map Operation
3.3.9 Pausing guidance
When you are driving a planned route but you do
not need guidance for a certain part of the route,
you can suspend it and continue when it is
needed again.
In the Navigation menu, tap to suspend
guidance.
3. Tap to save the location .
To add your home and work address to the saved
locations, perform the following steps:
1. On the Navigation view, tap , ,
Tap to resume guidance. and
3.4 Saving a location
To add any location to the saved locations (the list 2. Tap or ,
of frequently used destinations), perform the
following steps: Tap to confirm your seltion.
1. Select a destination as described before. It can be
an address, a Place, any location on the map, a 3. You can search for the address as described .
previously used destination from History, and so on.
Planning a route to one of the saved locations is
2. When the map appears with the selected location described .
3.4.1 Editing a saved location
in the middle, tap . To edit a location that you have already added as
a Saved Location, perform the following steps:
1. On the Navigation view, tap , ,
and
2. The list of Saved locations is displayed.
4. (optional) Using the keyboard, you can change the
name offered for the Saved Location.
59WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 60
iGo map Operation
3.3.9 Pausing guidance
When you are driving a planned route but you do
not need guidance for a certain part of the route,
you can suspend it and continue when it is
needed again.
In the Navigation menu, tap to suspend
guidance.
3. Tap to save the location .
To add your home and work address to the saved
locations, perform the following steps:
1. On the Navigation view, tap , ,
Tap to resume guidance. and
3.4 Saving a location
To add any location to the saved locations (the list 2. Tap or ,
of frequently used destinations), perform the
following steps: Tap to confirm your seltion.
1. Select a destination as described before. It can be
an address, a Place, any location on the map, a 3. You can search for the address as described .
previously used destination from History, and so on.
Planning a route to one of the saved locations is
2. When the map appears with the selected location described .
3.4.1 Editing a saved location
in the middle, tap . To edit a location that you have already added as
a Saved Location, perform the following steps:
1. On the Navigation view, tap , ,
and
2. The list of Saved locations is displayed.
4. (optional) Using the keyboard, you can change the
name offered for the Saved Location.
60WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 61
iGo map Operation
3.Tap and . 3. Tap .
4. Tap the location you want to edit,
tap and enter the name of the l
ocation on the keyboard, then tap .
Note：
In Saved Locations, Home and Work cannot be
renamed. To change your home or work 4. Scroll down the list and tap
location, tap or , 5. Select the type of the Alert Point, the direction from
which you expect the alert, and (if applicable) the
and confirm the address change. speed limit for this Alert Point.
5. Tap .
Adding a location to the list of saved locations is
described on page
3.5 Adding an Alert Point
You can save any map location as an Alert Point,
for example a speed camera or a school zone.
1. If you would like to save an Alert Point for the
first time, switch on the . In the Navigation menu, 6. Tap to save the location as a new
Alert Point.
tap , , then .
3.6 Running a Simulation
Switch on and confirm your To run a simulated navigation that demonstrates the
planned route, perform the following steps:
selection.
1. Tap on the Navigation view to access
Note： the Navigation menu.
IThe warning for road safety cameras is
disabled when you are in a country where road
safety camera warning is prohibited. However, 2.In the Navigation menu, tap .
you must make sure that using this feature is
legal in the country where you intend to use it.
2. Return to the Navigation view, and select the
Alert Point. The red cursor ( ) appears there.
61WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 62
iGo map Operation
3.7.1 Switching to off-road navigation
3. Tap . To switch to off-road navigation, perform the
following steps:
1. On the Navigation view, tap , ,
and
2. Tap and select .
Most of the procedures described for on-road
4. Tap . The simulation starts from navigation also apply to off-road navigation. Howev-
er, there are some that are not available in this
the starting point of the route and leads you through navigation mode. For example:
the whole planned route using a realistic speed.
*You cannot open the itinerary as you have no
maneuvers just route points and straight lines
between them.
*There are no route alternatives and route
planning method.
*Vehicle settings are disabled.
3.7.2 Selecting the destination in off-road mode
Selecting a destination (waypoint or final destina-
tion) is the same as described in the previous
(optional) You have the following controls during the sections. The only difference is that route points are
simulation (the control buttons disappear after a few linked to form a route with straight lines regardless of
seconds but you can open them again if you tap the the road network and traffic regulations.
map): 3.7.3 Navigating in off-road mode
The real difference between on-road and off-road
: Jump to the next route event (maneuver). modes is the navigation itself. When you are on the
Navigation view with an off-road route:
*Your position and heading is not aligned to the
: Pause the simulation. nearest road. There is no turn-by-turn navigation, just
a recommended direction.
: Jump to the previous route event *You can see an orange line drawn between your
(maneuver). current position and the next destination to reach.
: Tap to increase the speed of the
simulation to 4, 8 or 16 times faster. Tap The Turn Preview field in the top left corner shows a
again to return to normal speed. compass with your bearing and the distance of the
next destination.
5. Tap to stop the simulation.
3.7 Off-road navigation
When first started, Epsilon Linux device calculates
routes using the road network of the maps provided
with the product. If you want to disregard roads
during navigation, you can switch to off-road mode,
for example when driving in a desert.
62WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 63
iGo map Operation
When you reach the final destination, the navigation 4.1.3 Road safety cameras and other proximity
ends. Alert Points There is a special proximity warning for
road safety cameras (like speed or red light cameras)
Note: If you do not want to use off-road naviga- and other proximity Alert Points (like schools or
tion, switch back to on-road navigation by railroad crossings). These Alert Points are not part of
Epsilon Linux device.
tapping and . You can add your own Alert Points.
The application can warn you when you approach
road safety cameras like speed cameras or dangerous
4 Reference guide areas like school zones or railroad crossings. You can
The following sections describe the different set up the different alert types individually in the
concepts and menu screens of Epsilon Linux device. Warnings settings.
The following warning types are available:
4.1 Concepts
The following sections describe and explain naviga- *Audio warning: beeps are played (if the voice
tion-related concepts. guidance language that you selected is a
4.1.1 2D/3D GPS reception natural voice) or the type of the alert can be
The GPS receiver uses satellite signals to calculate its announced (TTS voice) while you are
(your) position and needs at least four signals to give approaching one of these points, and an extra
a three-dimensional position, including elevation. alert warns you if you exceed the given speed
Because the satellites are moving and because *Visual warning: the type of the Alert Point, its
objects can block the signals, your GPS device might distance and the related speed limit appear on
not receive four signals. If three satellites are the Navigation view while you are approach-
available, the receiver can calculate the horizontal ing one of these locations.d limit while
GPS position but the accuracy is lower and the GPS approaching.
device does not give you elevation data; only 2D
reception is possible. Several factors have an impact For some of the Alert Points, either the enforced or
on the deviation between your real position and the expected speed limit is available. For these points,
one given by the GPS device. For example, signal the audio alert can be different if you are below or
delay in the ionosphere or reflecting objects near the above the given speed limit.
GPS device have a different and varying impact on
how accurately the GPS device can calculate your *Only when speeding: The audio alert is only
position. played when you exceed the given speed
limit.
4.1.2 Natural and TTS voices
Natural voices are the traditional type of voice *When approaching: The audio alert is always
instructions. Every phrase that occurs in voice played when approaching one of these Alert
guidance messages is recorded in a studio with a real Points. In order to draw your attention, the
person. The advantage of pre-recorded voice is that it alert is different when you exceed the speed
sounds really natural, but the range of instructions limit.
that can be given this way is limited. Location-specif-
ic information such as street names cannot be Note: The warning for road safety cameras is
announced. TTS technology provides a usually disabled when you are in a country
machine-generated way to give voice instructions. where road safety camera warnings are
The advantage of TTS is that it can announce street prohibited. Make sure that using this feature
names, traffic events, route summary, and traffic is legal in the country where you intend to
rules. operate. Use it on your own responsibility.
You can also disable Alert Point warnings
manually. See page page 73 for instructions.
63WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 64
iGo map Operation
4.1.4 Route calculation and recalculation *Visual warning: The current speed limit is
A route is a sequence of route events, that is, maneu- shown on the map when you exceed it (for
vers (for example, turns and traffic circles) to reach
the destination. The route contains one starting example ).
point and one or more destinations. The starting
point is the current (or last known) position by
default. If you need to see a future route, the starting You can also choose to see the speed limit sign on
point can be replaced with any other given point. the map all the time.
Once the destination has been selected, Epsilon 4.1.7 Intelligent navigation
Linux device calculates the route based on your With the help of intelligent navigation, the planned
preferences. These preferences are the route route can adapt to traffic and other changes during
planning method and the road types used or navigation. The following sections describe these
avoided when calculating the route. For detailed features.
information on all the preferences, see Route 4.1.7.1 Congestion detour on highways
preferences settings. V2 device may offer a detour when you slow down
on a highway due to a traffic jam. The Potential
V2 device automatically recalculates the route if you congestion detour window appears and shows the
deviate from the proposed itinerary. length and duration of the detour.
4.1.5 Smart Zoom
Smart Zoom provides the following features:
* While following a route:
When approaching a turn, it zooms in and
raises the view angle to let you easily
recognize your next maneuver. If the next turn
is at a distance, it zooms out and lowers the
view angle to be flat so you can see the road in
front of you.
4.1.7.1 Congestion detour on highways
* While driving without a planned route: V2 device may offer a detour when you slow down
Smart Zoom zooms in if you drive slowly and on a highway due to a traffic jam. The Potential
zooms out when you drive at a high speed. congestion detour window appears and shows the
length and duration of the detour.
4.1.6 Speed limit warning You can ignore this message and keep the original
Maps may contain information about the speed
limits of the road segments. Epsilon Linux device is route by tapping or you
able to warn you if you exceed the current limit. This
information may not be available for your region, or can check the suggested route by tapping .
may not be fully correct for all roads on the map.
Speed warning can be fine-tuned in Warnings.
You can also set the relative speed tolerance above
which the application initiates the warning.
The following warning types are available:
*Audio warning: You receive a verbal warning
when you exceed the speed limit with the
given percentage.
64WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 65
iGo map Operation
By tapping the plus/minus signs, you can increase or
decrease the distance to avoid on the highway. You
can accept the recommended detour by
tapping .
4.1.7.2 Real-time alternative routes
V2 device may offer an alternative route on normal
roads in case of a traffic jam. The possible alternative
route window appears and shows the length and
duration of the detour. By tapping and , the
selected parking place becomes your destination.
4.1.7.4 Hints upon detour
If you leave the planned route by exiting a freeway,
Epsilon Linux device tries to guess the reason for
making a detour. The Reason for detour window
appears and shows available gas stations, restaurants
or other Places around the current position. Also, if
You can ignore this message and keep the original there are avoidable parts of the original route ahead
(like a tunnel, a toll road or a ferry), you can find them
route by tapping or you can check the in the list, in case you want to bypass them.
suggested route by tapping .
You can accept the recommended detour by
tapping .
By tapping one of the Places, Epsilon Linux device
creates a waypoint and navigates you to the selected
place. You can ignore them by tapping .
4.2 Useful Information menu
4.1.7.3 Parking around destination
If you leave the planned route by exiting a freeway,
Epsilon Linux device tries to guess the reason for
making a detour. By tapping , you can open a
top-down map with the recommended parking
Places around the destination. By tapping the
arrows on the sides, you can switch between the The Useful Information menu provides various
recommended parking facilities. additional functions. It can be found in the Naviga-
tion menu.
65WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 66
iGo map Operation
Button Description
Shows information on the current
position (latitude, longitude, nearest
town, next crossing street, and so on)
or the last known position if GPS
reception is not available.
Offers assistance near your current *By tapping the current street name if it is
position. displayed below the current position marker on
the map.
Offers a list of countries with useful
driving information about the selected
country (for example speed limits,
maximum blood alcohol level).
Shows statistical data of your trips, like
the start time, end time and average
speed. Track logs, the sequence of the
positions given by the GPS receiver, can The following information is shown on the Where
be saved together with the trip logs. Am I screen:
They can later be displayed on the map.
* Address details (when available) of the current
position
Shows the exact sunrise and sunset *Latitude and Longitude (coordinate of the
times for all your route points. current position in WGS84 format)
* The nearest town Next crossing road/street
* Previous crossing road/street.
You can also perform some actions on this screen.
Shows the GPS Information screen
with satellite position and signal Tap and to add the current
strength information.
position to the saved locations and to check the
country information.
4.2.1 Where Am I
This screen contains information about the current You can also search for assistance near your current
position (or about the last known position if GPS
reception is not available). You can access it the position. Tap to open a new screen for
following two ways:
quick search and select a category. For detailed
*By going to the Navigation menu and information.
tapping and .
66WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 67
iGo map Operation
4.2.2 Trip Monitor 4.3 Settings menu
Trip Monitor logs information about your route. You can configure the navigation settings, and
modify the behavior of Epsilon Linux device, by
You can record a new trip by tapping and tapping and .
stop it by tapping .
Tap the arrows to view the content of other pages.
By tapping on the Trip Monitor screen, you can
select the following options:
Button Function
By selecting a recorded trip, you
can delete, rename, or change the
color of the recorded route.
reception is not available.
Note: Changing some of these settings may not
have an effect in your current region if the
map data do not contain the required
You can export all logs into the information. .
sdmmc folder.
The Settings menu provides the following options:
You can access the Trip Monitor Button Function
Settings, where you can enable
saving the trip logs automatically
or you can save the trip logs Select the road types used in
manually. route planning, and the route
planning method.
By tapping your recorded trip on the Trip Monitor
screen, you can check information such as time,
speed, altitude and distance.
Set up voice guidance.
Enable and set up warnings for
speed limit, Alert Points (such as
speed cameras).
Fine-tune the appearance of the
Navigation view or adjust how the
By tapping on the Trip Data Details screen, software helps you navigate with
you can view the trip on the map, export track logs, different kinds of route-related
and check the elevation and speed profiles. information on the Navigation
view.
67WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 68
iGo map Operation
Button Function Button Function
Change the voice guidance Gives a quick route if you can
language, set the time zone, the travel at or near the speed limit on
measurement units, the time and all roads. Usually, the best
date formats, and customize the selection for fast and normal cars.
application for your local
language. Results in a route with fewer turns
Turn the automatic trip log saving and no difficult maneuvers. With
on or off and check the current this option, you can make Epsilon
size of the trip database. Linux device take, for example, the
freeway instead of a series of smaller
roads or streets.
Modify the basic software parame- Gives a short route to minimize
ters set during the initial set-up the travel distance. It can be
process. optimal for slow vehicles. Search-
ing for a short route regardless of
the speed, this route type is rarely
4.3.1 Route preferences settings optimal for normal vehicles.
The following settings determine how routes are Gives a quick but fuel-efficient
calculated: route based on the fuel consump-
tion data. Travel cost and CO2
Button Function emission calculations are estima-
tions only. They cannot take
Optimize the route calcula- elevations, curves and traffic
tion for different situations conditions into consideration.
and vehicle types by
changing the planning 4.3.1.2 Navigation Mode
method.
You can switch between on-road and
Select on-road or off-road off-road navigation by
navigation.
tapping and selecting .
4.3.1.3 Road types
To let the route fit your needs, you can also set which
Select your preferred road road types are to be considered for or to be excluded
types for the route. from the route. Excluding a road type is a preference.
It does not necessarily mean total prohibition. If your
destination can only be accessed using some of the
4.3.1.1 Route Planning Method types excluded road types, they are used only as much as
You can select from the following route planning necessary.
method types: In this case, a warning icon is shown on the Route
information screen, and the part of the route not
matching your preference is displayed in a different
color on the map. The following road types are
available:
68WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 69
iGo map Operation
Button Description
You might need to avoid freeways when you are driving a slow car or you
are towing another vehicle.
Charge roads are pay roads where you can purchase a pass or vignette to
use the road for a longer period of time. They can be enabled or disabled
separately from toll roads.
Per-use toll roads are pay roads where there is a per-use charge in the routes
by default. If you disable toll roads, Epsilon Linux device plans the best toll-free
route.
Epsilon Linux device includes ferries in a planned route by default. However,
a map does not necessarily contain information about the accessibility of
temporary ferries. You might also need to pay a fare on ferries.
Car shuttle trains are used to transports vehicles for a relatively short
distance and they usually connect places that are not easily accessible on a
road, for example, in Switzerland.
Carpool or HOV lanes can be used if a given number of passengers is
traveling in the vehicle. Check whether you are allowed to use carpool lanes
before enabling this road type.
Epsilon Linux device excludes unpaved roads by default. Unpaved roads can
be in a bad condition and you usually cannot reach the speed limit on them.
4.3.2 Sound settings You can modify the following settings:
Button Function
Disable verbal instructions. This function is enabled by default.
Set whether you want an immediate announcement for the next maneuver after
each turn, or it is enough to receive the information when the turn is near.
Set the verbosity of the voice instructions, that is how much they tell and how
often they speak.
*Minimal: the voice instruction is given once right before the next maneuver.
*Medium: the voice instruction is given when approaching the next maneuver
and it is repeated right before the maneuver.
*Verbose: the voice instruction is given first relatively far from the next maneuver,
it is repeated when approaching the next turn, and it is repeated again right before
the actual maneuver.
69WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 70
iGo map Operation
4.3.3 Warnings settings
You can enable and modify the following settings:
Button Description
V2 is able to warn you if you exceed the current speed limit. This information may not be
available in your region, or may not be fully correct for all roads on the map. This setting lets you
decide whether you wish to receive visible and/or audible warnings. The following warning
types are available:
*Visual warning: the current speed limit is shown on the map when you exceed it.
*Audio and Visual warning: besides the current speed limit being shown on the map, you also
receive a verbal warning when you exceed the speed limit with the set percentage. If you prefer
to see the speed limit sign on the map all the time (normally, it is shown only if you exceed the
limit), you can set it here. You can also set the relative speed above which the application
initiates the warning by adjusting a slider.
The value can be different within and outside towns.
Tap it to receive a warning when approaching a road safety camera or other Alert Points like
school zones or railroad crossings. You must make sure that using this feature is legal in the
country where you intend to use it. You can set the warning type for the different Alert Point
categories (alert types) individually. The following warning types are available:
*Visual warning: the type of the Alert Point, its distance, and the related speed limit appear on
the Navigation view while you are approaching one of these locations.
*Audio and Visual warning: besides the visual alert, beeps are played (when using a natural
voice) or the type of the alert is announced (in case of a TTS voice) while you are approaching
one of these points, and an extra alert warns you if you exceed the given speed limit while
approaching. For some of the Alert Points, the enforced or expected speed limit is available. For
these points, the audio alert can be different if you are below or above the given speed limit.
* Only when speeding: The audio warning is only played when you exceed the given speed
limit.
*When approaching: The audio warning is always played when approaching one of these Alert
Points. In order to draw your attention, the audio alert is different when you exceed the speed
limit.
Maps may contain driver alert information that can be shown on the Navigation view in a
similar way as real-life road signs. Tap it to enable or disable the warning for these road
segments (for example, dangers and sharp curves). For each category of warning signs, set the
warning type (visual or audio and visual) and the distance from the hazard to receive the
warning at.
70WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 71
iGo map Operation
4.3.4 Navigation View settings
These settings allow you to fine-tune the appearance of Button Function
the Navigation view. You can also adjust how the
software helps you navigate with different kinds of Show or hide the 3D elevation of
route-related information on the Navigation view. the terrain.
Tap to adjust the navigation view to your
Turn on Track Logs to show them
needs, choose suitable color themes from the list for on the map or turn them off.
both daytime and nighttime use, show or hide 3D Select which Places to show on
buildings, landmarks, and manage your Place visibility the map while navigating. Too
sets (which Places to show on the map). many Places make the map
crowded so it is a good idea to
keep as few of them on the map as
possible. Tap the name of the
Place category to show/hide it or
to open the list of its subcatego-
ries.
You can modify the following additional settings on the
Navigation View screen:
You can modify the following settings:
Button Function
Button Function If you are navigating with a
planned route, you can set three
Adjust the basic zoom and tilt data fields to be displayed on the
levels to your needs. Three levels Navigation view. You can choose
are available. from the time of arrival at destina-
tion, distance to destination, time
Select the color scheme used in to destination, time of arrival at
daytime mode. Daytime colors waypoint, distance to waypoint,
are bright and similar to paper time to waypoint, heading, or
road maps. altitude. Without a planned route,
there is only one data field that
Select the color scheme used in can be set to show the heading or
night mode. Night colors are the altitude.
darker to keep the average
brightness of the screen low. Turn the Route Progress Bar on or
off. If turned on, an orange line is
Show or hide 3D landmarks (3D displayed on the side of the
representations of prominent or screen, and a blue arrow on it
well-known objects). shows your progress.
Show or hide 3D city models (3D Turn it on to get freeway service
block representation of full city information (for example gas
building data containing actual stations, restaurants) or turn it off if
building size and position on the you do not need it.
map).
71WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 72
iGo map Operation
Button Function Button Function
Select the service types displayed It displays the current written
for the freeway exits. Choose from language of the user interface.
the Places categories. Tap it to select a new language
from the list of available languag-
Zoom out and show an overview es. The application restarts after
of the surrounding area if the next you change this setting and
maneuver is far and you are confirm it.
driving on a freeway. When you
get close to the event, the normal It shows the current voice
map view returns. guidance profile. Tap it to select a
new profile from the list of
Whenever adequate information is available languages and speakers.
available, lane information similar Tap any of these to hear a sample
to the real ones on road signs voice prompt. Just tap when you
above the road is displayed at the have selected the new spoken
top of the map. Tap it to turn this language.
feature on or off. Different voice profiles are capable
of different levels of service:
In certain situations, Epsilon Linux *Natural Voice (street names not
device offers a detour when there announced): These pre-recorded
is a traffic jam on a highway. sounds can only tell you basic
information about turns and
In certain situations, Epsilon Linux distances.
device offers an alternative route *TTS Voice (street names
when there is a traffic jam on the announced): These computed
road. voices can read out complex
In certain situations, Epsilon Linux instructions, street names or
device offers parking Places when system messages.
you approach your destination.
You can set the measurement
In certain situations, Epsilon Linux units and time/date format to be
device offers different route used. Epsilon Linux device may not
alternatives when you leave the support all the listed units in some
planned route and suddenly exit voice guidance languages.
the freeway.
By default, the time zone is taken
4.3.5 Regional settings from the map information and
You can modify the following settings: adjusted by your current location.
Here you can manually set the
time zone and the daylight saving
time.
4.3.6 Trip Monitor settings
Trip logs contain useful information about your
recorded trips. You can enable and modify the
following settings:
72WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 73
iGo map Operation
Button Decription Solution 2: Search for another address that is close to
the destination.
Trip monitor can record statistical Solution 3: Search for the coordinates or a nearby Place
data of your trips. If you need of Interest.
these logs later, you can let the 5.3 The calculated route is not optimal Issue:
application save them automati- The planned route is too long or includes several minor
cally for you. roads.
Track logs, the sequence of the Cause: In , the route planning
positions given by the GPS
receiver, can be saved together method is not set to the optimal parameter.
with trip logs. They can later be
displayed on the map. You can let Solution: Select your preferred route planning method
the application save track logs by performing the following steps:
whenever it saves a trip.
This is not a button. This line shows 1: Tap , , and .
the current size of the trip
database, the sum of all trip and
track logs saved. 2. Tap and select your
5 Troubleshooting preferred route, for example .
This section offers possible solutions to issues that may
occur during the operation of Epsilon Linux device.
5.1 GPS signal cannot be received Issue:
The current location is not available, because GPS signal
cannot be received.
Cause 1: GPS signal is weak or may not be available if
you are between tall buildings, in garages or tunnels as
the signal weakens or distorts as it travels through solid
material.
Solution 1: Go to a place where there is a clear sight of 5.4 Disabling the speed limit warning Issue:
the sky or at least a bigger part of the sky is visible. The speed limit warning is signalling even when the
Cause 2: It may take several minutes to receive GPS actual speed limit is kept.
signals when first using Epsilon Linux device, or when Cause: The speed limit in the digital map data might
your last known position is farther away from your differ from the actual speed limit of your current
current position. location.
Solution 2: Wait a few minutes for the GPS signal. Solution: Disable the speed warning by performing the
following steps:
5.2 Address cannot be found Issue:
V2 cannot find the address you entered.
Cause: The digital map data may not include every
single address. 1: Tap , , and .
Solution 1: If the house number is not known or V2
cannot find it, select only the street name. This way, V2
will navigate you to the midpoint of the street, where 2. Tap ,
you can find the exact address more easily.
and .
73WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 74
iGo map Operation
5.5 Keyboard buttons are grayed out Issue:
Some keyboard buttons are grayed out and cannot be
used.
Cause: V2 has a smart keyboard for address search,
which means that only those buttons are active that
can be used to type a name that is available on the map.
Solution: Check if you entered the name correctly. If the
name is correct, then the address you are looking for is
not available in the digital map data.
6 Copyright note
The product and the information contained herein are
subject to change without prior notification.
This manual may not, in whole or in part, be reproduced
or transmitted in any form either electronically or
mechanically, including photocopying and recording,
without the express written consent of Epsilon.
© 2024 - Epsilon © 2006 – 2024 TomTom.
All rights reserved. This material is proprietary and the
subject of copyright protection, database right protec-
tion and other intellectual property rights owned by
TomTom or its suppliers. The use of this material is
subject to the terms of a license agreement.
Any unauthorized copying or disclosure of this material
will lead to criminal and civil liabilities.
All rights reserved.
74WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 75
iDataLink Maestro
iDataLink Maestro check that it operates properly.
Keep your factory features and expand your -Functions and displays vary depending on the
level of in-riding connectivity with motorcycle model. For details on the function
Soundstream V2 and iDatalink Maestro RR. available for each model refer to the informa-
When your V2 receiver is installed in a compati- tion on our website.
ble motorcycle using the iDatalink Maestro RR -For trouble shooting information about
interface (sold separately), you’ll be able to iDatalink functions, visit the following website:
enjoy the performance and features of the V2 http://maestro.idatalink.com/support
receiver plus touchscreen control over key
factory audio features. Limitations
- The data is transmitted to this product from
Soundstream V2 supports factory functions via your motorcycle system via connected iDatalink
the iDatalink Maestro RR interface including: adaptor. Therefor, the actual data connects
Steering Wheel Controls, Gauges, Motorcycle displayed on your product may differ from the
info, Media Player (including USB ports), contents on the screen described in this
Hands-Free Telephone, Voice Commands, manual.
Satellite Radio. -When information on your motorcycle or on
Beside, user canuse the handle bar to control the devices in your motorcycle is sent from the
every mode GUI via cursor. iDatalink Maestro module, a screen notifying
you of such information may pop-up.
Using iDatalink
You can access the radio source provided for Activating iDatalink Maestro
the motorcycle. The motorcycle information Before using and/ or connecting the iDatalink
and many OEM systems such as steering Maestro adaptor, you will need to first flash the
controls, rider safety systems, and etc. can be Maestro RR module with the appropriate
displayed on Soundstream V2 by connecting motorcycle and Soundstream V2 firmware.
the optional iDatalink adaptor. It is also possible 1. Find the device number (7 characters) on the
to add visual screen such as gauges, motorcycle label on the packaging of this
information. However, an extra interface product or on the product itself.
module is required to access these features. 2. Access the following website and follow the
on-screen instructions to configure the desired
Note: Since the type of module varies depend- firmware.
ing on the motorcycle model, search for your http://maestro.idatalink.com/
motorcycle via the following URL to determine
which features are available for each module. Note:
Remember to select the correct radio model for When the serial number input is required, input
accurate results. the device number of this product.
http://maestro.idatalink.com/support 3. Install the motorcycle Soundstream V2
firmware on your iDatalink Maestro module.
Important: 4. Connect this product to the iDatalink Maestro
-For details about motorcycle models that are and install this product to the motorcycle.
compatible with iDatalink adaptor, refer to the The iDatalink function will be active.
information on our website.
-After installing the iDatalink adaptor, be sure to
75WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 76
iDataLink Maestro
Compatible w/ iDataLink® Maestro® RR Gauges:
CANBUS Integration Module Tap the Gauges icon on the main menu, will
The V2 headunit can display up to 10 digital display below:
gauges, offering a selection from over 50
available options. You can receive pop-up
warnings for oil pressure, fuel level, engine
temperature, and more. The programming of
handlebar thumb controls is customizable. V2
activates Boom 1, Boom 2, and HD Audio OEM
amplifiers. The wire harness is prepared for
iDataLink® Maestro® RR® and RR2® integration.
Displaying detection Motorcycle information
Note: You can definite the Guage function as
CAUTION your required.
This function is intended solely to assist the
rider know the Motorcycle status. It does not
detect all warnings .
NOTE:
This function is only available for motorcycles
equipped with an iDataLink Maestro box.
Motorcycle Info:
Tap the Motorcycle Info on the main menu, will
display below:
1 2 Displaying detection Motorcycle information list:
1. Fuel low (fuel level warning: 15%)
3 3 2. OIL pressure low( less than 10psi)
3. Engine Temperature high
【 Higher than 280°F degree (138° C)】
4.TPMS low [Front: 32psi (223KPA)
Rear: 36psi (248KPA) 】
4 5 6 5.Battery level warning: (Less than 12v)
1. Tap to back to home page. Once Dismiss, the top icon will flush, untill
2. 5 signal icons: Turn Left / Lowbean / Highbean the problem solve.
/Brake / Turn Right .
3. Show TPMS information.
4. Show the Voltage information.
5. Show the Motorcycle Engine status.
6. Show the EITMS status.
76WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 77
Camera in
Handlebar control the headunit: Cursor
When programme the idata module box, you can
definite the handlebar key’s function one by one.
And you can use the rocker button to make the
left/right /up /down cursor to operate every
page.
Left HandControl Cursor
Camera View
For connecting a camera.
Displaying the picture from the
Camera
RightHandControls The camera view screen is displayed when
you enter the Camra in.
Note:
V2 can support 720p high resolution
camera in.
Up
Left Right
Enter
Down
77WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 78
Specification
GENERAL
Power Requirement: DC 10 - 16Volts,
Power Requirement: Negative ground
Current Drain: 15A (Max.)
RMS Power Output: – Typ 4 x 30 W /4 Ω @ 14.4 V, 1 kHz THD =
10%
– Typ 4 x 25 W /4 Ω @ 14.4 V, 1 kHz THD = 1%
– Typ 4 x 50 W/2 Ω @ 14.4 V 1 kHz THD =10 %
Speaker Impedance: 2- or 4-Ohm Load
Frequency Response: 20Hz ~20KHz
Operating temperature: -20~60 ℃
Dimensions: 230mm(W) x 210mm(D)x 140mm(H)
TFT Display
TFT Screen size: 8.3 – Inch TFT/LCD
Resolution 1256x536 pixels
FM RADIO SECTION
Frequency Range 87.5 – 107.9 MHz (America)
87.5 – 108 MHz (Europe)
Usabe Sensitivity (S/N=30dB) ≤15dB
S/N Ratio: ≥55dB
Stereo Seperation ≥30dB
AM RADIO SECTION
Frequency Range (America) 530 – 1710 KHz
(Europe) 522 – 1620 KHz
Usabe Sensitivity (S/N=20dB) ≤40dB
S/N Ratio: ≥45dB
Line-out / Subwoofer Output
Maximum Output Leve (10K ohms load): ≥4 V RMS
Subwoofer Time Align 0~18ms
78WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 79
Trouble Shooting
Problem Cause Correct action
Check fuse Replace fuse
No Power, Dead. Consult your Local Specialist.
Incorrect wiring www.MotorcycleAudio.com/Spe
cialist-Locator
1. Turn off the unit.
2. Remove all wires attached to
the power antenna lead.
No sound output when Power antenna lead is Check eachwire for a possible
operating the unit with shorted to ground short to the ground using an
amplifiers or power excessive current is ohm meter.
antenna attached. required or remote on 3. Turn on the unit.
the amplifiers or power 4. Reconnect each amplifier
antenna remotewire to the power antenna
lead one by one. If the amplifiers
turn off before all wires are
attached, use an external replay
to provide remote-on voltage
(excessive current required)
Poor performance of Move the Motorcycle to
radiostation Weak signal another place, then tryagain
Volume is in minimum. Adjust volume to the desired
level.
No Sound or Audio The wiring is not properly
connected Check wiring connection.
79WHD14+ V2 / V2 / Soundstream V2 — Owner’s Manual, page 80
FCC Notes
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equip-
ment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
www.MotorcycleAudio.com
Follow Us on Social Media
30