6.5-inch Speakers for 2014+ Harley-Davidson Touring

Full document text

The complete text of the Installation Manual for PPHD14.652 (6 pages), extracted from the supplier PDF; pages without a text layer were transcribed from the page image. Check wiring and settings against the original PDF before cutting or splicing.

PrecisionPower®
Absolutely State of the Art Mobile Audio™

6.5” SPEAKERS FOR 2014+ HARLEY DAVIDSON®
TOURING SERIES MOTORCYCLES

FAIRING REMOVAL, STREET GLIDE & ULTRA

1. Remove three outer fairing bolts using a T27
Torx screw driver. The three outer fairing bolts
are located below the windshield. Remove the
windshield, store it and the screws removed in
a safe place for re-installation later.

TIP: Reinstalling the center screw after removing the windshield will
prevent the outer fairing from falling during the next step. A few turns by
hand will be sufficient.

2. Remove four inner fairing bolts using a T27 Torx screw driver. The four
inner fairing bolts are located adjacent to each turn indicator mounting
bracket and below/adjacent to each speaker. Store these screws in a safe
place for re-installation later.

3. While straddling the front wheel fender, grasp the outer fairing, remove
the center outer fairing bolt from the previous step, then gently pull the
fairing apart from the bike. With the fairing slightly pulled away from the
bike, disconnect wire harness for the headlamp and any other accessories.
Lay the fairing on a protected flat surface to prevent damage.

SPEAKER INSTALLATION, STREET GLIDE & ULTRA

1. Detach two cable clips from the top edge of the fairing support bracket,
adjacent to the outside gauges using a clip pry tool.

2. Use a mini flat-head screw driver to help disconnecting the harness
connectors for the two outside gauges

3. Detach the cable clip for the cigarette lighter cable using a clip pry tool
at the brake side speaker pod & unplug the cigarette lighter.

4. Disconnect the speaker wire connector for each speaker pod & detach
any other cable clips that are attached to each speaker pod using a clip
pry tool.

5. Remove two screws for the upper fairing support bracket to each speaker
pod  using a 5/32 hex screw driver. Set the screws aside for installation
later.

6. Loosen the two main wire harness tray screws under the head unit using
a Phillips screw driver. The main wire harness tray will fall slightly. Set the
screws aside for installation later.

7. Remove three bolts for each speaker pod at the fairing bracket, adjacent
to the main wire harness tray, under the head unit. Use a 7/16 socket on
small extension or universal joint, or a right angle 3/16 hex key tool. Set the
screws aside for installation later.

8. Remove three bolts attaching each speaker pod to the inner fairing
using a 3/16 hex screw driver. Each pod should be loose, set them aside.

9. Remove three screws attaching each speaker grill to the inner fairing
using a T25 Torx screw driver. Set the screws aside for use later.

10. Align & attach a metal PrecisionPower Street Glide grill to either side of
the inner fairing using the previously removed screws & a T25 Torx screw
driver.

11. Remove four screws holding the speaker to each speaker pod using a
T25 Torx screw driver. Set the screws aside for installation later.

12. Remove the speaker from the speaker pod & detach the speaker wire
terminals.

13. Trim a small locator pin on the face of each speaker pod using a utility
knife.

SPEAKER INSTALLATION, STREET GLIDE & ULTRA

14. Place a step filter into each speaker pod and connect the speaker wire
terminals to the corresponding male terminals of the step filter.

15. Connect the female connectors of the step filter to the corresponding
terminals of the PrecisionPower speaker.

16. Attach each speaker to the speaker pod with the four screws removed
in step 11, using a T25 Torx screw driver.

17. Align each speaker pod back in the fairing, & attach it to the inner
fairing with the three bolts removed in step 8, using a 3/16 hex screw
driver.

18. Attach each speaker pod to the fairing bracket with the bolts removed
in step 7, using a 7/16 socket on small extension or universal joint, or a
right angle 3/16 hex key tool.

19. Attach the main wire harness tray with the screws removed in step 6,
using a Phillips screw driver.

20. Secure each speaker pods to the upper fairing support bracket with
the two screws removed in step 5, using a 5/32 hex screw driver

21. Reconnect the speaker wire connectors to each speaker pod &
reattach any cable clips detached in step 4.

22. Reconnect the cigarette lighter connector to the cigarette lighter &
reattach its cable clip removed in step 3 to the brake side speaker pod.

23. Reconnect the wire harness connectors for each outside gauge
removed in step 2.

24. Reattach two cable clips to the upper fairing support bracket detached
in step 1.

FAIRING INSTALLATION, STREET GLIDE & ULTRA

1. While holding the outer fairing, straddle the front wheel fender. Reconnect wire harness for the headlamp and any other accessories previously disconnected. Gently reset the outer fairing, paying attention to any cables that need to be tucked away inside. Reinstall the center outer fairing bolt removed previously.

2. Reinstall the four inner fairing bolts removed previously using a T27 Torx screw driver. The four inner fairing bolts are located adjacent to each turn indicator mounting bracket and below/adjacent to each speaker.

3. Reset the windshield and reinstall the three outer fairing bolts removed previously using a T27 Torx screw driver. The three outer fairing bolts are located below the windshield.

SPEAKER INSTALLATION, ROAD GLIDE
1. Remove each speaker grill by wedging a plastic/nylon pry tool between
the inner fairing and grill edge, popping it outward.

2. Remove four screws holding the speaker to each speaker pod using a
T25 Torx screw driver. Set the screws aside for installation later.

3. Remove the speaker from the speaker pod & detach the speaker wire
terminals.

4. Trim a small alignment pin on the face of each speaker pod using a utility
knife.

5. Place a step filter into each speaker pod and connect the speaker wire
terminals to the corresponding male terminals of the step filter.

6. Connect the female connectors of the step filter to the corresponding
terminals of the PrecisionPower speaker.

7. Attach each speaker to the speaker pod with the four screws removed
in step 1, using a T25 Torx screw driver.

8. Snap in a corresponding metal PrecisionPower Road Glide grill to either
side of the inner fairing.