Model HDHU.14Si
Also listed as: HDHU.14 Si
Owner’s manual and specifications for the HDHU.14Si head unit.
| Power Requirement | DC 10 - 16Volts, Negative ground |
|---|---|
| Current Drain | 15A (Max.) |
| Maximum Power Output | 50Watts x 4 |
| RMS Power Output | 25Watts x 4 |
| Speaker Impedance | 2- or 4-Ohm Load |
| Frequency Response | 20Hz ~20KHz |
| Operating temperature | -20~60 ℃ |
| Dimensions | 230mm(W) x 210mm(D)x 140mm(H) |
| TFT Screen size | 7 – Inch TFT/LCD |
| Resolution | 1024x600 pixels |
| Line-out / Subwoofer Output | ≥4 V RMS |
Source: Owner’s Manual, Soundstream. Wording and values are retained from the supplier document.
The complete text of the Owner’s Manual for HDHU.14Si / HDHU.14 Si (30 pages), extracted from the supplier PDF; pages without a text layer were transcribed from the page image. Check wiring and settings against the original PDF before cutting or splicing.
RESERVE Owner's Manual EN OEM UPGRADE HEAD UNIT FOR 2014+ HARLEY DAVIDSON® MOTORCYCLES HDHU.14Si RESERVE Gauges Ignition is OFF 94.3°F INTAKE TEMP PEAK 1784 MMM RPM 48 MPH 67.2% TWIST GRIP 13.4V VOLTAGE SETTINGS PAGE 1 | PAGE 2 BACK RESERVE Works with Apple CarPlay android auto IPx6 WATERPROOF FACEPLATE MOSFET MAX 75W × 4 2 Ω Speaker SOUNDSTREAM TECHNOLOGIES idataLINK maestro ((SiriusXM)) READY Bluetooth HDHU.14 Si
Contents Safety First
Safety First Safety Definitions
Safety Definitions 2 Statements in this manual preceded by following
words are of special significance:
Pre-Riding
Check list 3 WARNING
Care and cleaning 3 WARNING indicates a potentially hazardous
Screen 3 situation which, if not avoided, could result
in death or serious injury.
Appearance 3
Accessories & Installation 4 WARNING
Installation 5 Set volume levels and other controls on
Panel Description 6 audio and electronic devices before riding.
Distractions can lead to loss of control,
Wiring 7
resulting in death or serious injury.
Harness 8
WARNING
Operation
Do not select a volume level that blocks out
Main menu 9 traffic noise or interrupts the concentration
Setting 9 necessary for the safe operation of the Motor-
Apple CarPlay/Android Auto 14 cycle. Distractions or a volume level that
Radio operation 16 blocks our traffic noise could cause loss of
USB operation 16 control resulting in death or severe injury.
Bluetooth Music 17
Bluetooth Phone 18
SiriusXM 19 Note
iData Link 25
Camera in 27 Pay attention while riding, keeping your eyes and
clear mind on the road. Some features are locked out
Specification 28 to prevent distraction, limited in capability while the
Trouble Shooting 29 Motorcycle isin motion. Even a part is available, donot
allow it to distract you from operating your
FCC Notes 30 Motorcycle safely.
For safety, program the system when stopped.
Perform system setup and get familiar with the
controls and features of the infotainmentsystem
before operating the Motorcycle on the road.
This system cannot warn about the safety of an area,
bad road conditions, and availability of emergency
services.
Use this radio only in locations where it is safe to do.
2Pre-RIDING Appearance
Check list
Configure the system with your personal
preferences before riding to use features and HDHU.14Si
minimize distractions while on the road
entirely.
1. Set brightness, background.
2. Configure presets.
3. Adjust audio settings like EQ, volume, fade,
balance etc. before ridding.
4. Pair, connect and set up phone features
through Bluetooth.
5. Connect USB devices for Apple CarPlay® or
Android Auto®. Front
6. Selectstation or media
7. Connect the iDataLink Maestro module for
Motorcycle Info and Gauage information
display.
CARE AND CLEANING
Use only HDHU.14Si recommended products
and methods to keep the radio, speakers, and
other audio system components clean and in
good condition.
Do not use any abrasives, polishes, or rubbing
compoundsto clean the screen or other
components. Do not use any ammonia-based
cleaners on the net.
The use of other products or methods may
cause damage to components.
Screen : Top
Do not use any chemical cleaners or
chemical-containing wipes or cloths.
These can cause damage to the screen
surface.
Gently clean the display glasssurface with a
clean, dry microfiber cloth. Before cleaning, it
is suggested to remove any visible dust, dirt,
sand particles with a gentle compressed
airstream.
Back
3Accessories and Installation Harness Included! Installation Use OEM head unit mounting locations & original screws 4
Installation
Note: Reinstall the OEM bracket after head unit installation
Installation
1 USB Connector
Connect the external USB cable for USB
device, Android smart phone, iPhone.
2 Radio Connector
Connect the Radio Antenna from
motorcycle.
3 Camera in
Connect the Camera in.
4 Camera +12 V DC (Max 0.5A)
Connect the Camera power cable.
5 External Microphone Connector
Connect the external Microphone cable.
6 6 Connect
SiriusXM Tuner Connector
1 2 5
the SXV300 tuner.
Note: SiriusXM SXV300 Tuner sold separately,
3 4 SiriusXM subscription required.
5Panel description
HDHU.14Si
1 4
2 5
3 6
1 Apple CarPlay® / Android Auto® 4 Home button
Press to enter CarPlay® / Android Auto® • Press to toggle between Home screen and
directly(When the iPhone/Android phone active media.
is connected). • Available selections: Radio, Apple
CarPlay®/Android Auto®, BT Music, BT
2 Siri Button（Voice Recognition） Phone, USB,Motorcycle Info, Gauge,Set-
When the iPhone/Android phone is tings, Camera in.
connected, press Siri button to start the
voice control function.
5 (Volume +)
3 Power / Mute • Press to increase the volume value.
• When the power is off, press to power
on. 6 (Volume -)
• When the unit is working, short pressing • Press to decrease the volume value.
for Mute, press again for unmute.
• Pressing and hold to turn the source unit
power off.
6Wiring
CAM +12V（Max 0.5A) (Pink)
Camera in (Yellow)
3.5mm Connection for Included
Bluetooth Calling Microphone
SXM Tuner(Not included)
RCA Low-Level Subwoofer Channel Output
HDHU.14Si Wire Harness
For Optional Subwoofer Amplifier (RCA not incl.)
OEM USB Cable Connector
(USB cable not included) RCA Low-Level Rear Channel Output
for Optional Speaker Amplifier (RCA not incl.)
RCA Low-Level Front Channel Output
for Optional Speaker Amplifier (RCA not incl.)
OEM Radio Antenna Connector
(antenna cable not incl.)
48 PIN CONNECTOR
E4. Pink/White............UART-SPEED L1. White/Black.........FL-
F4. Gray/White...........UART-TX L2. White.......................FL+
G4. Blue/White...........UART-RX L3. Black.........................Ground
H1. Green/Black.........RL- L4. Black.........................Ground
H4. Red/White............UART-12V M1.Gray.........................FR+
J1. Green.......................RL+ M2.Gray/Black...........FR-
J3. Orange/Whike...Illumination M3.Yellow.....................Battery+
J4. Black/White.........UART-GND M3.Yellow.....................Battery+
K1. Purple......................RR+
K2. Purple/Black........RR-
K3. Blue...........................ANT
K4. Red...........................ACC
7Included Harness
Harness! Connect to Motorcycle: Connect to HDHU.14Si (Headunit):
1. CAN- （Green/White) 3- Pin Connector
8. RL-（Green/Black) 3
Black......................... Ground
9. RL+ （Green) Red.............................ACC
10. RR+(Purple)
1
Yellow......................Battery
11. FL-(White/Black) 4- Pin Connector
12. FR+(Gray) Blue/White...........UART-RX
1
13. CAN+( Purple/White) Gray/White..........UART-TX
14. Remote Control(Blue) Black/White.........UART-GND
4
22. RR-(Purple/Black) Red/White............UART-12V
23. FL+(White)
24. FR-(Gray/black) 10- Pin Connector
35. GND(Black) 2 1 Orange/White............Illumination
36. Battery +(Yellow) Pink/White....................SPD
42. UART-RX(Blue/White) Blue/White....................UART-RX
10
47. GND(Black)
9 Blue....................................Remote Control
48. Battery + (Yellow) Blue....................................Remote Control
18- Pin Connector
CAN+.................... Green /White
CAN-...................... Purple /White
Connect to External Amplifier:
Rr
Connect to iDatalink Maestro Rr2 Compatible：
Note: The Maestro Box is not included.
8Main Menu Settings
HDHU.14Si is a headunit for Motorcycle Touch the icon to enter the Setup menu.
withthe following functions: The Setup menu is included System Settings,
Apple CarPlay®, Android Auto®, Radio, USB, BT Display Settings, Audio & EQ Settings, Bluetooth
Music, Phone, Camera, Motorcycle Info, Settings.
Gauges, SiriusXM ready .
Touch the corresponding Mode icon to enter
playing mode. The Mode icon in gray means
the corresponding function is not ready, or
the proper device has not been connected.
System Settings：
The System Settings allow the user to set up
the Language, Date & Time, Key Beep,
Factory Reset and About
System Settings
Language
Date & Time
Hidden soft button bar: Key Beep
Normal
A hidden pop up soft button bar is located Camera View
at the bottom. Touch the icon to shown Factory Reset
the soft button bar. Touch the to hidden. About
Dimming, to change Daylight or Language：
Night.
Language
Setup, to enter the Settings Menu.
Bluetooth pairing.
EQ, to enter the Equalizer setting
menu.
Date & Time:
To setting Time display format (12H or 24H),
setting the date and time
Date & Time
9Settings
Touch Key Color
Camera View : Normal / Reverse.
To set the camera view is Normal or Reverse. Touch Key Color
Auto Changing Color ON
Key Beep: On / Off Selectable Color
To set the touch button beep tone is On or Off.
Factory Setting:
To default the default factory settings:
Factory Reset
Auto Changing Color: On/Off .
ON: The Led color will change automatically.
OFF: You press the button or
to select desired color.
Color: White / Red / Orange / Yellow /Blue / Green /
About: Purple / Cyan.
To display the HDHU.14Si hardware and
firmware version.
About Background Wallpaper:
User can select the preset wallpaper or select
prefer picture in USB driver as the wallpaper.
Background Wallpaper
Press + to download a custom, JPG background wallpaper image
from a USB flash drive, or select from the options below...
Display setting:
Below is the Display setting menu, user can
select Nighttime Brightness,Touch Key
Color,Background Wallpaper. Touch the corresponding picture to select
the prefer background.
Display Settings
Touch “ + “, the head unit will search the USB
-8 photo file for wallpaper.
Nighttime Brightness
Select a picture and touch ”OK” to add the
Touch Key Color wallpaper.
Background Wallpaper
Select another picture for replacing
the current wallpaper.
Nighttime Brightness : -15 – 0. (Default is -8).
10Settings
Audio & EQ Setting About the Crossover
Below shown is the Audio serring Menu. This unit is equipped with an active crossover. The
crossover limits the frequencies delivered to the
outputs.
The crossover adjusts the HPF (high pass filter) or LPF
(low pass filter) of speakers and subwoofer, and also
the slope (how fast the filter rolls off the highs or
lows).
Adjustments should be made according to the
reproduction characteristics of the speakers.
Depending on the speakers, a passive network may
not be necessary. If you are unsure about this point,
Balance/Fader:
please consult your authorized Alpine dealer.
Touch the + or – of Balance/Fade to tune
for the driver and passenger preference.
The value of Balance (Left 12 – Right 12) • HPF (high pass filter): Cuts the lower frequencies and
and Fader (Front 12 – Rear 12). allows the higher frequencies to pass.
Touch Reset to set both Balance and Fader • LPF (low pass filter): Cuts the higher frequencies and
to zero. allows the lower frequencies to pass.
Audio & EQ Settings • Slope: The level change (in dB) for a frequency change .
• The higher the slope value, the steeper the slope
becomes.
• Do not use a tweeter without the HPF set on, with a
high cut-off frequency, otherwise damage may occur to
the speaker due to the low frequency content.
• Adjustment should be made according to the
recommended crossover frequency of the connected
speakers. Determine the recommended crossover
13-Band Equalizer: frequency of the speakers. Adjusting to a frequency
13-band of EQ tuning, slide the EQ bar to tune range outside that recommended may cause damage
each band frequency level according to use to the speakers.
preference. For the recommended crossover frequencies of
Touch Reset button to sell all Band to zero. speakers, refer to the respective Owner’s Manual.
We are not responsible for damage or malfunction of
speakers caused by using the crossover outside the
recommended value.
Or user can touch “<” or “>” at the bottom to
select the following preset EQ:
Off, Soft Rock,Pop,Electric,Jazz, EQ Custom.
11Settings
Front/ Rear Crossover: Subwoofer Phase: 00 or 1800
User can touch “<” or “>” to select the 00 or 1800
AMP Turn-on Delay: ON /OFF.
User can set AMP Turn-on Delay is ON or OFF.
Volume Settings:
User can set Source Level / Maximum Volume.
Slope： 12dB / 24dB
User can touch “<” or “>” to select the desired
frequency Value.
Subwoofer Settings:
Source Level Adjust.
0
0
0
0
0
Subwoofer Output: ON or OFF. SiriusXM 0
Subwoofer Level: -10~+10 User can adjust the source mode (Radio,
Subwoofer Crossovers: USB, BT Audio,Apple CarPlay, Andriod Auto,
SiriusXM) gain value. The gain can be
adjusted from -10~0 seperatedly.
Maximum Volume Adjust.
Set Low Pass Crossover
Frequency & Slope.
Slope： 12dB / 24dB Maximum Volume Level : ON or OFF.
Set High Pass Crossover Frequency & Slope.
Maximum Level Adjust: 40~50
User can touch “<” or “>” to select the desired
frequency Value.
12Settings
Bluetooth Settings：
Touch the Bluetooth Settings from the setting
menu will be shown below:
Bluetooth Settings
00:03
Connection ON
Pairing >
Device Name:
Clear Records >
Connection : On/Off (Select Bluetooth connection
is On or Off).
Pairing: To start the paring.
Bluetooth Settings
00:03
Paring Mode
From Bluetooth device connection
Cancel
Device Name : Shown the connected phone or
device name.
Clear Records: To clear the device list records.
13Apple CarPlay® & Android Auto®
Apple CarPlay :
Starting procedure of using Apple CarPlay
You can operate iPhone applications with
1 Connect an Apple CarPlay compatible
finger gestures such as tapping, dragging,
device to this unit via USB.
scrolling, or flicking on the screen of this
2 Touch the Apple CarPlay icon.
product.
The Apple CarPlay home screen appears.
Compatible iPhone models
For details about compatibility of iPhone You can use Apps of connected iPhone. The
models, refer to the following website. items displayed and the language used on the
https://www.apple.com/ios/carplay screen differ among the connected devices.
To enter the Apple CarPlay mode, touch Apple
WARNING Carplay icon on the Home selection screen.
Certain uses of the iPhone may not be legal
while driving in your jurisdiction, so you must
be aware of and obey any such restrictions. If 1
in doubt as to a particular function, only
perform it while the car is parked. No feature
should be used unless it is safe to do so under
the driving conditions you are experiencing.
Notes on using Apple CarPlay 2
• iPhone with iOS 7.1 or later is required.
Update to the latest iOS version before use.
3
• Apple CarPlay can be used on iPhone 5 or
later.
• For details on compatible models, refer to 1 Application keys
the compatibility list on the support site on the
back cover. Start the application.
• For details about Apple CarPlay, refer to the
manual supplied with your iPhone, or visit the 2
website of Apple CarPlay.
Display the home screen of Apple CarPlay.
• Since the GPS on your iPhone is used, place
Touch and hold to active Siri.
your iPhone where it can easily receive a GPS
signal 3 Home
Exit the Apple CarPlay screen and displays
• You can use Siri function by touching Home screen.
button once Apple CarPlay is activated
• The Bluetooth connection with the Apple * The icon design may change depending
CarPlay compatible device will be terminated on the iOS version.
automatically if Apple CarPlay is turned on.
• Hands-free phoning via Bluetooth wireless
technology is not available while Apple
CarPlay is on.
14Apple CarPlay® & Android Auto®
Android Auto®:
You can operate Android applications with
finger gestures such as tapping, dragging,
scrolling, or flicking on the screen of this 1
product
Starting procedure of using Android Auto
2
1 Connect an Android Auto™ compatible
device to this unit via USB.
2 Touch the Android Auto icon.
The Android Auto home screen appears
Note: 3
• You can use Voice function by touching
button once Android Auto is activated. 1 Application keys
• The Bluetooth connection with the Android Start the application.
Auto compatible device will be terminated
2 Home
automatically if Android Auto is turned on.
• Hands-free phoning via Bluetooth wireless Exit the Android Auto screen and displays
technology is not available while Android Home screen.
Auto is on. 3 Operation Bar
Notes on using Android Auto Starts the application or displays informa-
• Android phone with Android 5.0 or higher is tion.
required. Update to the latest OS version
before use.
• Your Android phone needs to support
Android Auto. For details on compatible
models, refer to the compatibility list on the
support site on the back cover.
• Download the Android Auto app on Google
Play.
• For details about Android Auto, refer to the
manual supplied with your Android phone, or
visit
• Since the GPS on your Android phone is used,
place your Android phone where it can easily
receive a GPS signal.
• Android Auto may not be available in your
country or region.the website of Android Auto.
15Radio USB
Touch “Radio” in the main menu to enter the for more than 3 seconds, then the preset button
radio interface. will be highlighted on the screen, and the preset
station will be stored.
Radio setting:
Touch “FM” can change between
FM1>FM2>FM3.
Touch “AM” can change between Radio Area: Select the region , America/Europe
AM1>AM2. /Eastern Europe /Japan /Southeast Asia /Latin
Touch “GOTO” then Pop-up the
GOTO menu and enter the desired America/ Asia / Australia.
Frequency Number. RDS: Switch ON or OFF.
TA: Switch ON or OFF.
AF:Switch ON or OFF.
PTY: Enter PTY list.
Note: AF is only for Europe region.
USB
Touch for Prescan search, each Plug the USB; the USB icon will be colorful.
scanned station will be played Touch the USB icon to enter the USB
for 10 sec, touch again to stop. playback mode. The source unit will
Touch to auto scan searching. playback the audio in the USB device.
Touch to enter EQ settings.
Touch to switch Local or DX.
Touch to enter Radio settings.
Short touch to seek down, long
touch to tune down.
Short touch to seek up, long
touch to tune up.
Preset channel, six preset buttons store and recall
stations for each band. Touch and slide the preset Press to go to the following folder.
channel can switch to next band FM1/FM2/FM3
or AM1/AM2.
Press to search Audio/Image files.
Store a Station
1. Tune radio to desired station.
Press to go to the previous folder.
2.Touch and hold the one of the preset station
16USB Bluetooth Music
Short press ti skip previous track.
.Long press to fast reverse. Press to search Audio files.
Play or Pause button.
Short press ti skip previous track.
Short press ti skip nexts track.
Long press to fast forward. Play or Pause button.
Press to select Repeat All>
Repeat 1> Repeat Folder. Short press ti skip nexts track.
Press to switch Randon is
On or Off. Press to select Repeat All>
Press to select Audio setting or Repeat 1> Repeat Folder.
set the preferred EQ of each Press to switch Randon is
band in custom mode. On or Off.
Press to select Audio setting or
File List Browsing set the prefer EQ of each band
in custom mode.
Touch to browse the folder and file
list of the USB device. Bluetooth Connect:
If the Bluetooth is not connected, press
Reconnect the paired Phone or paring to pair
the new device.
Select Audio or Music files.
Select Picture files.
Return to playing previous file. Bluetooth Pairing:
Pairing screen will be shown as below:
Bluetooth Music:
Touch the BT Music icon to enter Bluetooth
Music playing mode. If the Bluetooth is
connected, the music will be playing as
below shown:
Turn on the Bluetooth of the Mobile phone/
Bluetooth device; you can see the
"SOUNDSTREAM HD."
Select the "SOUNDSTREAM HD" for paring
and connection.
17Bluetooth Phone
Bluetooth Phone: SOUNDSTREAM HD
After the mobile Phone is connected with
the source unit via Bluetooth(HFP), the
user can go through the source unit.
Make a phone call. Touch the Phone icon in
Main Menu to go to BT Phone mode.
Please note it needs to connect the
microphone for phone calls.
SOUNDSTREAM HD Receive an incoming call:
If the Phone is connected with the source
unit via Bluetooth, when an incoming call,
below screen will be shown:
Press to answer the incoming call.
Press to reject the incoming call.
SOUNDSTREAM HD
Keypad. Tap it to enter call mode.
History. Tap it to show the call record,
missed, received and dialed calls.
Contact. Tap it to show the phonebook
of connected device.
BT Setup. Tap it to set Auto answer and
Microphone gain. SOUNDSTREAM HD
Make a call or Accept the incoming call.
Backspace, tap it to clear the incorrect
dial digit.
Make a Call:
1. Touch the icon to enter dial screen.
2. Using the keypad , touch 0-9,*,# , enter the
Interchange between phone and source unit.
desired number to dial. If you input an
incorrect number, touch the icon on the
ON / OFF the Microphone function.
keypad to delete the incorrect number.
3. Once hte correct bumber appears on the
screen, touch the icon to go to daling Display the Keypad.
interface.
4 To end the call, touch the icon
on the screen.
18Bluetooth Phone SiriusXM Operation
SiriusXM Ready
Call List: SiriusXM is where moments happen. The widest,
Touch the icon to display the deepest variety of music, ad-free. More games,
call combined list. more sports, more coverage than anywhere. The
SOUNDSTREAM HD
most extensive entertainment, complete news
coverage and every kind of comedy. Listen in your
car, on your phone, online and at home. A SiriusXM
Vehicle Tuner and subscription are required. For
more information, visit www.siriusxm.com.
Activating your SiriusXM Subscription after
installing your SiriusXM Connect Vehicle Tuner and
antenna, power on your Headunit and select
SiriusXM mode. You should be able to hear the
Slide the bar at the right up and down to SiriusXM preview channel on Channel 1. If you
display a call logs. cannot hear the preview channel, please check the
installation instructions to make sure your SiriusXM
Contacts: Connect tuner is properly installed.
Touch the icon to access the phone After you can hear the preview channel, tune to
book of the connected mobile Phone. Channel 0 to find the Radio ID of your tuner. In
To make a call from the phonebook,simply addition, the Radio ID is located on the bottom of the
touch the contact’s name SiriusXM Connect Vehicle Tuner and its packaging.
You will need this number to activate your subscrip-
SOUNDSTREAM HD tion. Write the number down for reference.
Note: the SiriusXM Radio ID does not include the
letters I, O, S or F.
In the USA, you can activate online or by calling
SiriusXM Listener care:
• Visit www.siriusxm.com/activatenow
• Call SiriusXM Listener Care at
1-866-635-2349
BT Setup: For Canadian Subscriptions, please contact:
• Visit www.siriusxm.ca/activate
• Call SiriusXM Customer Care at
1-888-539-7474
As part of the activation process, the SiriusXM
satellites will send an activation message to your
tuner. When your radio detects that the tuner has
received the activation message, your radio will
display “Subscription Updated”.
Once subscribed, you can tune to channels in your
Auto Answer On/Off, incoming call auto subscription plan. Note, the activation process
answer. usually takes 10 to 15 minutes, but may take up to an
MIC Gain: Low /Middle /High hour. Your radio will need to be powered on and
receiving the SiriusXM signal to receive the activation
message.
19SiriusXM Operation
To enter SiriusXM mode, touch the SXM icon on User Interface Operation
the Main Menu: Press FM or AM keys to toggle between
SXM & FM/AM radio mode
Press the SXM key to toggle between
three preset groups
Press the ALRT key to view current
song and/or artist alerts
Press the Channel Browse key to scroll
channel listings by category
Press the Direct Tune key to enter a
If the CHECK TUNER message appears, verify all specific channel number to tune
connections are complete. Confirm the Vehicle Press the EQ key to open the 10-band
Connect Tuner is connected, as well as the equalizer settings
antenna for the Vehicle Connect Tuner.
Press the Settings icon to access
SiriusXM
settings specific for SiriusXM mode
Press the Next or previous channel
keys to advance channels
Press any preset key to tune the stored
channel. To store a preset, tune to the
desired channel, then press & hold on
When successfully connected, the user interface the preset location for 3 seconds.
will appear: Artist & Song Alerts
SiriusXM
While listening to SiriusXM Satellite Radio, you can
mark Artists and/or Songs for which you wish to be
alerted. The radio will display an Alert message
whena matching artist or song is found on another
channel. Then you can choose if you want to tune
to that favorite or you can ignore the alert and stay
on your current channel. To save an artist or song
title, press on the artist name or song title on the
SiriusXM Channel Logos are displayed in the user screen. Then, confirm again to save the favorite.
interface, providing a graphical representation of SiriusXM
the current channel tuned.Album art can be
displayed for most of the SiriusXM music
channels. When album art is not available, the
channel logo or the SiriusXM logo will be
displayed.
Note: Compatible with SXV200 or later tuner
models. Not all music channels contain album
art images.
20SiriusXM Operation
SiriusXM At any time, press the content key on the
1 [Artist Alert] 10,000 Maniacs
right side to view the artist, title, & other
Ch 22: Ch0022Sid362Cat01 information about the song/content currently
2 [Artist Alert] Pearl Jam playing on the channel(s) listed.
Ch 21: Ch0021Sid363Cat01
My Music
Press the MyMusic key to view all stored artist &
song title alerts. Press the red X at right of any
undesired alerts to delete it. Temporarily disable
Channel Browse any alert by deselecting the check box left of
Press the Browse key to scroll channel listings any alert.
by category or all available channels. Disable all alerts by sliding the switch on top to off.
Channel List
SiriusXM
Press Ch. List to view all available channels in My Music Alerts
numeric sequence. Scroll the list to the desired
channel, then select within the channel row to
tune the channel.
SiriusXM
Direct Tuning a Channel
Press the Direct Tune key to enter a channelnumber
My Music
to tune. Enter the channel number using the
keypad pop-up, then select the green check
box to confirm your selection. If a number is
Category List entered in error, press the red backspace keyto
Press Cat. List to view all available channels in erase the last digit.
category sequence.
SiriusXM
SiriusXM
My Music
Select a category by pressing the left or right
arrows above the channel list. Scroll the
corresponding category’s channels below, press
a channel name to tune the channel.
21SiriusXM Operation
13-Band Equalizer SiriusXM
Press the 13-Band Equalizer key to access the
audio equalizer settings. Return to the Audio &
EQ Settings section of this owners manual (pg.
11) for more information.
Then, the channel list will appear to scroll the
subscribed channels. Select any channel(s) to lcok.
When a channel is successfully locked, a lock icon
will appear adjacent to the channel name.
SiriusXM
SiriusXM
SiriusXM Settings Menu
Press the settings icon to enter the SiriusXM
settings menu.
SiriusXM
Change Passcode
Select Change Passcode to change the
passcode required to activate the parental lock
feature and to lock & unlock channels. A
passcode pop-up will appear, requesting the
current passcode. Enter the 4-digit passcode,
then select the green check box to
confirm. If a number is entered by mistake,
Parental Controls press the red backspace key to erase the
The Parental Lock feature can be used to block last digit. The default passcode is 0000.
user selected channels from playback. To SiriusXM
enable the parental lock, slide the virtual switch
to ON. The switch should illuminate orange. A
passcode pop-up will appear, requesting the
parental lock passcode. Enter the 4-digit
passcode, then select the green check
box to confirm. If a number is entered by
mistake, press the red backspace key
to erase the last digit. The default passcode is
0000.
22SiriusXM Operation
Then, another passcode pop-up will appear, Then, the channel list will appear to scroll the
requesting the new passcode. Enter the 4-digit subscribed channels. Select any channel(s) to
passcode, then select the green check lock or unlock. If a channel is successfully locked,
box to confirm. If a number is entered by a lock icon will appear adjacent to the channel
mistake, press the red backspace key to name.
erase the last digit.
SiriusXM
SiriusXM
Then, a third & final passcode pop-up will
appear, requesting to enter the new passcode
again to the green check box to confirm.
If a number is entered by mistake, press the red
backspace key to erase the last digit.
SiriusXM
Lock Channel
Select Lock Channel to lock or unlock channels
from playback. A passcode pop-up will appear,
requesting the current passcode. Enter the
4-digit passcode, then select the green check
box to confirm. If a number is entered by
mistake, press the red backspace key to
erase the last digit. The default passcode is 0000.
SiriusXM
23SiriusXM trouble shooting
Advisory Message Cause Explanation / Solution
-Verify that the antenna cable is connected to the
SiriusXM Connect Vehicle Tuner.
The radio has detected a fault with theSiriusXM -Inspect the antenna cable for damage and kinks.
Check Antenna antenna. The antenna cable maybe either Replace the antenna if the cable is damaged.
disconnected or damaged. -SiriusXM products are available at your local car
audio retailer or online at:
shop.siriusxm.com/all-parts/
The radio has difficulty communicatingwith the
Verify that the SiriusXM Connect Vehicle Tuner
Check Tuner SiriusXM Connect Vehicle Tuner. The tuner may
cable is securely connected to the radio
be disconnected or damaged.
-Verify that your vehicle is outdoors with a clear view
of the sky.
-Verify that the SiriusXM magnetic mount antenna is
mounted on a metal surface on the outside of the
vehicle.
-Move the SiriusXM antenna away from any
The SiriusXM Connect Vehicle Tuner obstructions.Inspect the antenna cable for damage
No Signal hasdifficulty receiving the SiriusXM satellite and kinks.
signal. -Consult the SiriusXM Connect Vehicle tuner
installation manual for more information on antenna
installation. Replace the antenna if the cable is
damaged. SiriusXM products are available at your
local car audio retailer or online at
shop.siriusxm.com/all-parts/
-Press OK to clear the message.
-In the U.S.A., visit www.siriusxm.com or call
1-866-635-2349 if you have questions about your
subscription.
The radio has detected a change in your SiriusXM
Subscription Updated subscription status.
-In Canada, visit www.siriusxm.ca/activate or call
CustomerCare at 1-888-539-7474 if you have
questions about yoursubscription.
shop.siriusxm.com/all-parts/
The channel that you have requested is nota valid
SiriusXM channel or the channelthat you were Visit www.siriusxm.com for more information about
Channel Unavailable listening to is no longeravailable. You may also the SiriusXM channel lineup.
see this messagebriefly when first connecting a
newSiriusXM Connect Vehicle tuner.
-In the U.S.A., visit www.siriusxm.com or call
The channel that you have requested is not 1-866-635-2349 if you have questions about your
included in your SiriusXM subscription package subscription.
Channel Unsubscribed or the channel that you were listening to is no -In Canada, visit www.siriusxm.ca/activate or call
longer included in your SiriusXM subscription CustomerCare at 1-888-539-7474 if you have
package. questions about yoursubscription.
shop.siriusxm.com/all-parts/
The channel that you have requested is Locked See the Parental Control section for more
Channel Locked by the radios Parental Control feature. information on the Parental Control feature and how
to access locked channels.
24iDataLink Maestro
iDataLink Maestro check that it operates properly.
Keep your factory features and expand your -Functions and displays vary depending on the
level of in-riding connectivity with motorcycle model. For details on the function
Soundstream HDHU.14Si and iDatalink Maestro available for each model refer to the informa-
RR. When your HDHU.14Si receiver is installed in tion on our website.
a compatible motorcycle using the iDatalink -For trouble shooting information about
Maestro RR interface (sold separately), you’ll be iDatalink functions, visit the following website:
able to enjoy the performance and features of http://maestro.idatalink.com/support
the HDHU.14Si receiver plus touchscreen
control over key factory audio features. Limitations
- The data is transmitted to this product from
The HDHU.14Si supports factory functions via your motorcycle system via connected iDatalink
the iDatalink Maestro RR interface including: adaptor. Therefor, the actual data connects
Steering Wheel Controls, Media Player (includ- displayed on your product may differ from the
ing USB ports), Hands-Free Telephone, Voice contents on the screen described in this
Commands, Satellite Radio. manual.
-When information on your motorcycle or on
the devices in your motorcycle is sent from the
iDatalink Maestro module, a screen notifying
Using iDatalink you of such information may pop-up.
You can access the radio source provided for
the motorcycle. The motorcycle information Activating iDatalink Maestro
and many OEM systems such as steering Before using and/ or connecting the iDatalink
controls, rider safety systems, and etc. can be Maestro adaptor, you will need to first flash the
displayed on HDHU.14Si by connecting the Maestro RR module with the appropriate
optional iDatalink adaptor. It is also possible to motorcycle and HDHU.14Si firmware.
add visual screen such as gauges, motorcycle 1. Find the device number (36 alphanumeric
information. However, an extra interface characters) on the label on the packaging of this
module is required to access these features. product or on the product itself.
2. Access the following website and follow the
Note: on-screen instructions to configure the desired
Since the type of module varies depending on firmware.
the motorcycle model, search for your motorcy- http://maestro.idatalink.com/
cle via the following URL to determine which
features are available for each module. Remem- Note:
ber to select the correct radio model for When the serial number input is required, input
accurate results. the device number of this product.
http://maestro.idatalink.com/support 3. Install the motorcycle/ HDHU.14Si firmware
on your iDatalink Maestro module.
Important: 4. Connect this product to the iDatalink Maestro
-For details about motorcycle models that are and install this product to the motorcycle.
compatible with iDatalink adaptor, refer to the The iDatalink function will be active.
information on our website.
-After installing the iDatalink adaptor, be sure to
25iDataLink Maestro
To enter Motorcycle info Mode, touch Displaying detection Motorcycle information
the Motorcycle info icon of the Main
Menu. CAUTION
The Motorcyle Information page will be shown This function is intended solely to assist the
as below: rider know the Motorcycle status. It does not
detect all warnings .
NOTE
This function is only available for motorcycles
equipped with an iDataLink Maestro box.
Indicate the Gearbox Postion information.
Indicate the driving direction. Displaying detection Motorcycle information list:
Indicate the battey information.
1. Fuel low (fuel level warning: 15%)
Indicate the Engine information.
2. OIL pressure low( less than 10psi)
To enter Gauges Mode, touch the 3. Engine Temperature high
【 Higher than 280°F degree (138° C)】
Gauges icon of the Main Menu.
4.TPMS low [Front: 32psi (223KPA)
The Gauges page will be shown as below: Rear: 36psi (248KPA) 】
5.Battery level warning: (Less than 12v)
Once Dismiss, the top icon will flush, untill
the problem solve.
Note: You can definite the Guage function as
your required.
26Camera in Camera View For connecting a camera. Displaying the picture from the Camera The camera view screen is displayed when you enter the Camra in. Camera in 01:55 27
Specification
GENERAL
Power Requirement: DC 10 - 16Volts,
Power Requirement: Negative ground
Current Drain: 15A (Max.)
Maximum Power Output: 50Watts x 4
RMS Power Output: 25Watts x 4
Speaker Impedance: 2- or 4-Ohm Load
Frequency Response: 20Hz ~20KHz
Operating temperature: -20~60 ℃
Dimensions: 230mm(W) x 210mm(D)x 140mm(H)
TFT Display
TFT Screen size: 7 – Inch TFT/LCD
Resolution 1024x600 pixels
FM RADIO SECTION
Frequency Range 87.5 – 107.9 MHz (America)
87.5 – 108 MHz (Europe)
Usabe Sensitivity (S/N=30dB) ≤15dB
S/N Ratio: ≥55dB
Stereo Seperation ≥30dB
AM RADIO SECTION
Frequency Range (America) 530 – 1710 KHz
(Europe) 522 – 1620 KHz
Usabe Sensitivity (S/N=20dB) ≤40dB
S/N Ratio: ≥45dB
Line-out / Subwoofer Output
Maximum Output Leve (10K ohms load): ≥4 V RMS
Subwoofer Time Align 0~18ms
28Trouble Shooting
Problem Cause Correct action
Check fuse Replace fuse
No Power, Dead. Consult your Local Specialist.
Incorrect wiring www.MotorcycleAudio.com/Spe
cialist-Locator
1. Turn off the unit.
2. Remove all wires attached to
the power antenna lead.
No sound output when Power antenna lead is Check eachwire for a possible
operating the unit with shorted to ground short to the ground using an
amplifiers or power excessive current is ohm meter.
antenna attached. required or remote on 3. Turn on the unit.
the amplifiers or power 4. Reconnect each amplifier
antenna remotewire to the power antenna
lead one by one. If the amplifiers
turn off before all wires are
attached, use an external replay
to provide remote-on voltage
(excessive current required)
Poor performance of Move the Motorcycle to
radiostation Weak signal another place, then tryagain
Volume is in minimum. Adjust volume to the desired
level.
No Sound or Audio The wiring is not properly
connected Check wiring connection.
29FCC Notes
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equip-
ment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
www.MotorcycleAudio.com
Follow Us on Social Media
30